﻿============================================================ WARNING =====================================================================
1. At BMC FW Ver 3.07, change the conf to 4MB, so yafuflash and webui does not support BMC upgrade from previous version to newer than v3.07.
Need use SOCFLASH at another package to upgrade it.
2. Befor version 3.05, yafuflash maybe take long time to start the updating process via In-band.

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v6.40.00
==========================================================================
Version: 6.40.00
Release Date: 2023.11.21
Code Based: 6.00

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.25)

[Firmware Images]:
1. rom.ima with checksum          :  E6238F50
2. rom.ima with MD5 checksum      :  43146DF182423A37FED1FCD29DC47B59
3. rom.ima_enc with MD5 checksum  :  4B8EBB837F40821A4A51BD807C5F35BA

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx:
[update] update yafuflash tool version , support RHEL 9 64bit update
[security] CVE-2023-37293/37294/37295/37296/37297 issue fix
[security] CVE-2023-34334 security issue with injection CVE-2023-34343 Changed system() to safe_system() for enhanced security 
[security] CVE-2023-34344 
[security] CVE-2023-34333 : Fix for memory mapping size not checked in videocap driver

[Bug Fixed]:
S5Bx/S5Sx:
[fix] #436561 , login SEL manufacturer ID not correct
[fix] #370367 , the amount of Drive are incorrect at "/redfish/v1/Systems/Self/Storage/RAID_FW-00000000".




[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
	5. After 5.65.00, TI DPS work around will reduce system performance about 2% during low power state. 
	6. Raid controller information function of WEBUI must wait a while after RAID initialize done.
	7. BMC FW can't support raid card function when raid card fw newer than MR7.19.
	8. S5B HBA 3816 doesn't verify yet.

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v6.30.00
==========================================================================
Version: 6.30.00
Release Date: 2023.8.01
Code Based: 6.00

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :  E61A94F7
2. rom.ima with MD5 checksum      :  DF225F2D1288081722E73C009ABB78CB
3. rom.ima_enc with MD5 checksum  :  56AFC7B2FA32BC6DB26D1EFFFD282784

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx:
[fix] fix TLS 1.0/1.1 won't disable when user doesn't use quanta default SSL certificate 
[fix] fix CVE2023-34329 security vulnerabilities

[Bug Fixed]:
S5Bx/S5Sx:
[fix] #320287 redfish command cannot display manufacturer ID "001c4c"
[fix] #300179 BIOS post error SEL format mismatch to BIOS SPEC




[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
	5. After 5.65.00, TI DPS work around will reduce system performance about 2% during low power state. 
	6. Raid controller information function of WEBUI must wait a while after RAID initialize done.
	7. BMC FW can't support raid card function when raid card fw newer than MR7.19.
	8. S5B HBA 3816 doesn't verify yet.


==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v6.20.00
==========================================================================
Version: 6.20.00
Release Date: 2023.4.28
Code Based: 6.00

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :  E61F5BD8
2. rom.ima with MD5 checksum      :  ECAD568CD020E3EBBA5B9180C8480D26
3. rom.ima_enc with MD5 checksum  :  CFE7A7FE2A3C7C80E8DDD9805B240B0D

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx:


[Bug Fixed]:
S5Bx/S5Sx:
[fix] #320287 redfish command cannot display manufacturer ID "001c4c"
[fix] #399919 DMI PCIE CE/UCE SEL format mismatch BIOS SPEC
[fix] #416492 Correctable ECC Logging Disabled SEL display wrong dimm slot number
[fix] #420736 BMC SNMP command sometime will timeout
[fix] #423123 system fan sometime will full speed for a while 



[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
	5. After 5.65.00, TI DPS work around will reduce system performance about 2% during low power state. 
	6. Raid controller information function of WEBUI must wait a while after RAID initialize done.
	7. BMC FW can't support raid card function when raid card fw newer than MR7.19.
	8. S5B HBA 3816 doesn't verify yet.

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v6.10.00
==========================================================================
Version: 6.10.00
Release Date: 2023.1.31
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :  E653A6F0
2. rom.ima with MD5 checksum      :  6CAC809FEA98D584A347FE656D552AD6
3. rom.ima_enc with MD5 checksum  :  ECD13DED0B0E7FA34DA0971DEB3C4E35

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx:


[Bug Fixed]:
S5Bx/S5Sx:
[Fix] #328227 BIOS Correctable ECC error SEL format mismatch to SPEC define
[Security] server vulnerability: User enumeration via API, modify web error code when user login fail
[Security] redfish security enhance for invalid password and non-existent user login


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
	5. After 5.65.00, TI DPS work around will reduce system performance about 2% during low power state. 
	6. Raid controller information function of WEBUI must wait a while after RAID initialize done.
	7. BMC FW can't support raid card function when raid card fw newer than MR7.19.
	8. S5B HBA 3816 doesn't verify yet.

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v6.00.00
==========================================================================
Version: 6.00.00
Release Date: 2022.10.28
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :  E64F7FBC
2. rom.ima with MD5 checksum      :  CA09E78832D3BADF244D0B00A4E996F4
3. rom.ima_enc with MD5 checksum  :  58B462BC5D2C114650B2742BB31EBA14

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx:
[update] worst card list R56

S5Bx/S5Sx:



[Bug Fixed]:
S5Bx/S5Sx:
[Fix] #403599 web ui didn't display notice infomation when user doesn't insert raid card
[Fix] #396239 web ui SMTP setting will popup error message
[Fix] #328227 to fit event log of BIOS SPEC .


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
	5. After 5.65.00, TI DPS work around will reduce system performance about 2% during low power state. 
	6. Raid controller information function of WEBUI must wait a while after RAID initialize done.
	7. BMC FW can't support raid card function when raid card fw newer than MR7.19.
	8. S5B HBA 3816 doesn't verify yet.


==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.92.00
==========================================================================
Version: 5.92.00
Release Date: 2022.08.03
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :  E651E354
2. rom.ima with MD5 checksum      :  2FB57DCF20894A0C396582C4E1746F7F
3. rom.ima_enc with MD5 checksum  :  6D349A44E3AFB340A72B29E0A1462192

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx:
1.[Update] update storlib to MR 7.17 , support raid card 3916 ( this update only support on S5B serials)

S5Bx/S5Sx:
1.[Update] update server security , disable unsafe protocol and cipher list


[Bug Fixed]:
S5Bx/S5Sx:
1.[Fix] #310203 upload key for LDAP startls will not work 
2.[Fix] #374643 #400256 SEL format mismatch with BIOS spec define
3.[Fix] #320287 BIOS update fail C4 type should show 001c4c manufactature ID
4.[FIX] #402432 yafuflash inband update fail


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
	5. After 5.65.00, TI DPS work around will reduce system performance about 2% during low power state. 
	6. Raid controller information function of WEBUI must wait a while after RAID initialize done.
	7. BMC FW can't support raid card function when raid card fw newer than MR7.19.
	8. S5B HBA 3816 doesn't verify yet.

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.80.00
==========================================================================
Version: 5.80.00
Release Date: 2022.06.10
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :  DBFBE690
2. rom.ima with MD5 checksum      :  A82E255BCB491BC8C9624E718C9AE478
3. rom.ima_enc with MD5 checksum  :  90719D5CA44AE8D23CDBCBA59EF66E3E

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx/S5Sx:
[Add] add solution for BMC pantsdown vulnerability issue 

[Bug Fixed]:
S5Bx/S5Sx:




[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
	5. After 5.65.00, TI DPS work around will reduce system performance about 2% during low power state. 

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.70.00
==========================================================================
Version: 5.70.00
Release Date: 2022.05.31
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :  DBFD6AD9
2. rom.ima with MD5 checksum      :  7C0AF9734EE5081734D0D0B7BCAE7136
3. rom.ima_enc with MD5 checksum  :  C84615739D0FF872C83A946573C88311

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx/S5Sx:
[update] Worst card list R54

[Bug Fixed]:
S5Bx/S5Sx:
[Fix] #387239 Sometmes RKVM mount iso link lost.



[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
	5. After 5.65.00, TI DPS work around will reduce system performance about 2% during low power state. 

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.65.00
==========================================================================
Version: 5.65.00
Release Date: 2021.02.21
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :    DBE7C659 
2. rom.ima with MD5 checksum      :    41688a4b1aeb62c9f21ddb584618ebb1
3. rom.ima_enc with MD5 checksum  :    531db3fbfdff90a5d82e2c15c085e3d8 

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx/S5Sx:
1. For TI DPS Chip bug, add workaround to check TI DPS chip checksum, if it doesn't match official suggestion version, BMC will write permanent settings to change TI DPS FW.


[Bug Fixed]:
S5Bx/S5Sx:
1.[Fix] #383317, can not delete user.
2.[Fix] #267517, some temp sensor <minimum sensor range> value is unreasonable.
3.[Fix] #310203, remove wrong network restart solution. use lighttpd API.
4.[Fix] #385188, #385118 web ui display message typo at raid card information.
5.[Fix] #385609, BMC will cold reset twice after reset BMC via redfish.



[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
3. After 5.65.00, TI DPS work around will reduce system performance about 2% during low power state. 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.56.00
==========================================================================
Version: 5.56.00
Release Date: 2021.11.26
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :     DDFC4F3B
2. rom.ima with MD5 checksum      :     6A48F248F18B728C386FF5A525E934D7
3. rom.ima_enc with MD5 checksum  :     4E36565B6D1A19D32C4E08B4087A97E3

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx/S5Sx:
1.add curl_targetoverwrite-1.0.4-ANY.spx to update curl 7.78 for CVEs
2.update openssl_1_0_1_wheezytargetoverride-1.3.0-ARM for update perl to 5.28 and openssh to 8.8 and openssl to 1.0.2u
3.add busybox patch for fix CVEs

[Bug Fixed]:
S5Bx/S5Sx:



[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.55.00
==========================================================================
Version: 5.55.00
Release Date: 2021.11.04
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :     E7096634
2. rom.ima with MD5 checksum      :     6D546CEFD8AA8BFC632CD671D17E6F68
3. rom.ima_enc with MD5 checksum  :     F7E1BEDCD0E1FEDDB50C64BDA4B9D6FB

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx/S5Sx:


[Bug Fixed]:
S5Bx/S5Sx:
1.[Fix] #377948, Airfolw and temp oulet reading error.
2.[Fix] #283949, GPU sensor abnormal.
3.[Fix] #328227 add sel_severity_warning to EvtTbl_EventLog.
4.[Fix] #372545, code base version mismatch
5.[Fix] #279348, support read VCA2 temp
6.[sync] sync S7D, #319726, add toshiba nvme ssd in QTMPNVMeMI_PCA9546_S7D on S5T.  
7.[Fix] #372935, BMC cold reset event generate error.
8.[Fix] #356426, modify Bios update event log to fit spec.
9.[Fix] #372905, modify event log to fit bios spec.
10.[Fix] #373081, exclude CAMELLIA in ssl.
11.[Fix] #366191, modify event log to fit bios spec.
12.[Fix] #374643, modify event string to fit bios spec.
13.[Fix] #265820, SNMP setting can not restore to default after restore default.


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.45.00
==========================================================================
Version: 5.45.00
Release Date: 2021.07.30
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :   E6EEA2DF  
2. rom.ima with MD5 checksum      :   8BBDB987F550F527A5E3F50E08ABD05E  
3. rom.ima_enc with MD5 checksum  :   EB6699828C0768A35424FD2555FBEB3D  

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx/S5Sx:
[change] For security request, exclude cmallia in ssl.cipher-list.
[modify] update worst card list rev 51
[modify] modify S5BV worst card level 4 for VCA2 support weight
[modify] Darby creek UNCT and UCT temp 

[Bug Fixed]:
S5Bx/S5Sx:
[Fix] #318027, modfiy user name length.
[Fix] #366855, follow bios spec modify parity event string.
[Fix] #328227, change event log to fit BIOS SPEC .
[Fix] #366191, follow bios spec change board id severity fron info to critical
[Fix] #283005, to match BIOS eventlog spc.
[Fix] #322915, add webui html smtp-setting's help to show.
[Fix] #333860, #328441 add micron NVME SSD temp read function on S5T.
[Fix] #276237, when fan fault asserted, the fan warning will deasserted.
[Fix] #261055 # 275008 modify memory DCPMM unknown error and DCPMM Scrub Uncorrectable severity  



[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.35.00
==========================================================================
Version: 5.35.00
Release Date: 2021.05.20
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :     E73B9D1B
2. rom.ima with MD5 checksum      :     56C99551098AD71332A37030B62E106E
3. rom.ima_enc with MD5 checksum  :     5F894E32C29BFF80977E2D75A8283799

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V04
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx/S5Sx:
1.[Modify] worst card list R50.
2.[Change] S5BM fantable to R04


[Bug Fixed]:
S5Bx/S5Sx:
1.[Fix] #275008, undefine DCPMM event.	
2.[Fix] #360951, RAID stripe size only have 64KB
3.[Fix] #261181, some string error on user setting page.
4.[Fix] #261729, checkbox error.
5.[Fix] #359940, Lost sensor "Volt_P3V_BAT"
6.[Fix] #357792, mask GPGPU sensor on webui
7.[Fix] #361489, BMC sometime does not record power on event issue
8.[Fix] #361808, It will trigger CPU throttling on AC when plug two power module and one core.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.25.00
==========================================================================
Version: 5.25.00
Release Date: 2021.03.05
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :   E73CD6E9
2. rom.ima with MD5 checksum      :   330EDADA7C95CAC031EC596328838BEE
3. rom.ima_enc with MD5 checksum  :   24603772B37C7D87A6AD8547EC1ED006

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V03
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx/S5Sx:
1.[Add] add source code for svn 92896.
2.[Modify] change X5M identify Board mechanism.
3.[Modify] worst card list R49.
4.[Add] add more x710 series OCP card define to support its FRU format.


[Bug Fixed]:
S5Bx/S5Sx:
1.[Fix] #317565, Event String self test result via webUI mismatch spec.
2.[Fix] #289839 pop up message of "stop media" is incorrect.
3.[Fix] #342700 Bus Fatal event parse need to meet BIOS spec.
4.[Fix] #342699, #342698, #342696, #342695 (bus0/dev0/fun0) did not match BIOS SPEC.
5.[Fix] #342694, #342693, #342691 (CPUX_XX) did not match BIOS SPEC.
6.[Fix] EIP 570452 Java RKVM quit unexpectly when use window OS and click Virtual Mediz Wizard.
7.[Fix] #272631, Modify RAID card logical device policy to fit spec.
8.[Fix] #275951, Unable to login webUI, if press the "enter" key many time.
9.[Fix] #343591, BMC may update failed by Redfish. Change SVN#92754 kill luajit position.
10.[Fix] #269876. sort function is abnormal on Raid Event log.
11.[Fix] #269214, #269228. Date can set on 2/30 withour error.
12.[Fix] #269841, RAID Event types show unknown.
13.[Fix] #288240,#288238, AD secret user name string length and won't popup error message.
14.[Fix] #344211, Correctable ECC(CPUX_XX) severity did not fit BIOS spec.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.13.00
==========================================================================
Version: 5.13.00
Release Date: 2020.10.30
Code Based: 5.11

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.24)

[Firmware Images]:
1. rom.ima with checksum          :    E73EA84C
2. rom.ima with MD5 checksum      :    17C43B69D42DD06963D8EE097DA40F31
3. rom.ima_enc with MD5 checksum  :    F8E248E9814EC8D2BC3DF3DD941A833A  

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU11~12: V03
SKU80~82: R20
SKU83~87: V12
SKU91~92: V03 

[Change/Add]: 
S5Bx/S5Sx:
1. [Modify] Update worst card list to R48
2. [Modify] (security)cont. with #5 Add string checking( including length, pattern) for XuanWu Vulnerability report for block release.
3. [Modify] (security)strlen length checking modification for XuanWu Vulnerability report
4. [Modify] disable TLS 1.0, 1.1

 
[Bug Fixed]:
S5Bx/S5Sx:
1. [Fix] #337912, close button show in webUI is different with pop up message
2. [Fix] #325027, BIOS image update event string
3. [Fix] #320287, GENID does not match ipmi spec.
4. [Fix] #288922, when User privilege login should show "Invalid Username of Password" not "User Privilege could not login".
5. [Fix] #289839, MIB version should be 1.13
6. [Fix] #339005, [workaround] kill Redfish service when upgrading BMC by WebUI or Yafu-flash. 
7. [Fix] sync S5G to avoid session will be full when login more than 20.
8. [Fix] #339005[workaround] kill Redfish service when upgrading BMC by WebUI or Yafu-flash.  

 
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.12.00
==========================================================================
Version: 5.12.00
Release Date: 2020.09.21
Code Based: 4.98

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.22)

[Firmware Images]:
1. rom.ima with checksum          :    E7408918
2. rom.ima with MD5 checksum      :    35BEB5FA53634815D49177C5EBADA55D
3. rom.ima_enc with MD5 checksum  :    CA1E7B3CD966374B14214AF310DB0DC3  

[Fan Table]
Version:
S5Bx:
SKU0~2: R20
SKU3~4: V12
SKU5~7: V12
SKU8~9: v11
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1.[Change] The Display error of lan 6 print, Should be one DHCPv6 and one SLAAC
2.[Modify] #309395,Mask SEL log to fit QCT spec.

[Bug Fixed]:
S5Bx/S5Sx:
1.[Fix] #331386 Change POST error sel log output
2.[Fix] #332429
3.[Fix] #336553 Delete AMI NTP EIP solution
4.[Fix] #311032 web UI show NA when user doesn't install the OCP card
5.[Fix] #328227 to fit event log of BIOS new SPEC .
6.[FIX] #336449 IPv6 router2 setting issue
7.[Fix] #260878. PEF function could not cancel from webui.
8.[Fix] #317565 delete space to fit spec
9.[Fix] #335168. Incorrect space in SNMP "agentSystemMac"
10.[Fix] #318027. user name rule
11.[Fix] #332375. webUI hot spare sync
12.[Fix] sync S5KQ solution to avoid smart PDU test fail.
13.[Fix] #335760,335758, run linux_oob-pc.sh to do BMC preserve update sometimes will crash.
14.[Fix] #315910. raid physical device power state discription 
15.[Fix] #333063. RAID event logs on WebUI will occur "No Records to display" when the log number is close to 999.
16.[Fix] #302471 correct software ID of NM Status
17.[Fix] #311606 sensor threshold of "Temp_Inlet"
18.[Fix] #328227 to fit event log of BIOS new SPEC.
20.[Fix] #297376 Moodify the HDD weight.
21.[Fix] #323315, POST error log is wrong.
22.[Fix] #331951 BMC can't set PSU cold redundancy mode when system use different power source
23.[Fix] #337139 sync SEL sevenity with spec.
24.[Fix] #335760,335758, run linux_oob-pc.sh to do BMC preserve update sometimes will crash.
 
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.11.00
==========================================================================
Version: 5.11.00
Release Date: 2020.07.31
Code Based: 4.98

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.22)

[Firmware Images]:
1. rom.ima with checksum          :   E72F4C6D 
2. rom.ima with MD5 checksum      :   FD398A46FE89E207306DCE5AA9CFAFF9 
3. rom.ima_enc with MD5 checksum  :   59334BDBBBB7257FB10BB18F3E6D0DF2 

[Fan Table]
Version:
S5Bx:
SKU0~2: R20
SKU3~4: V12
SKU5~7: V12
SKU8~9: v11
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. [add] S5BV support Nvidia A100
2. [update] worst card list R45 
3. [Modify] Modify S7D PCIe error patch

[Bug Fixed]:
S5Bx/S5Sx:
1. [Fix] sync EIP 551047 to fix user exit SMASH without close SOL will cause BMC CPU full loading
2. [Fix] Fix etrack 330718 & 330763,the sensor name doesn't sync with spec. [PCIE Error...PCIe Error],[Critical IRQ...Critical INT],[Memory Error Event...Memory Error Dis]

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v5.10.00
==========================================================================
Version: 5.10.00
Release Date: 2020.07.17
Code Based: 4.98

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.22)

[Firmware Images]:
1. rom.ima with checksum          :    E7281137
2. rom.ima with MD5 checksum      :    498252FA22B5B77AAA33DC7D2650A39B
3. rom.ima_enc with MD5 checksum  :    6BD7BC145DA9F49FBC414314A77F270D

[Fan Table]
Version:
S5Bx:
SKU0~2: R20
SKU3~4: V12
SKU5~7: V12
SKU8~9: v11
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. [Add] sync AMI Raid card solution to improve stabolity.
2. [Modify] Remove the "io policy" field in Raid card setting of webui.
3. [Update] sync EIP 538292,CVE-2019-20636 security update.
4. [Add] Upload S5BE FPGA power/amp ddf.
4. [Restore] reverse PCIE error slot offset , because only S7D platform need to change and it will use patch.
5. [Add] MKT request, add SKU19.
6. [Update] worst card list R44
7. [Change] change fan duty, all fan zone duty should be 100% when one fan rotor occurs in any zone.
8. [Add] Support S5BE w/FPGA(20), S5BE wo/FPGA(21) . 

[Bug Fixed]:
S5Bx/S5Sx:
1. [Fix] sync AMI EIP543861. Fix WebUI cannot login if disable IPMI channel 1, Remove the IPMI channel access check.
2. [Fix] Fix the Common Name validation in SSL Generate page is not match with help hint and SPEC.
3. [Fix] Fix #310203, LADP setting, when upload certicifation file then save, network would not auto restart to aitivate setting.
4. [Fix] PSU_status presence event will happen during AC cycle.
5. [Fix] Fix #323272, BIOS Post error event log doesn't match SPEC.
6. [Fix] Fix S7D sensor's softwar ID/Slave Address. Sync with S5B. e-track#323857
7. [Fix] PHY board cannot use shared-NIC after AC-cycle or BMC cold reset.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 


==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v4.98.00
==========================================================================
Version: 4.98.00
Release Date: 2020.04.30
Code Based: 4.90

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.22)

[Firmware Images]:
1. rom.ima with checksum          :  E7A21A8D 
2. rom.ima with MD5 checksum      :  CC30E9C0F5CA9BBD97658F653AB69AEA 
3. rom.ima_enc with MD5 checksum  :  80A9B12DA0B7E9166F526C73DFC9D60C

[Fan Table]
Version:
S5Bx:
SKU0~2: R20
SKU3~4: V12
SKU5~7: V12
SKU8~9: v11
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. [Change] Renew Java certification.
2. [Modify] Modify the format of dimm serial number. (Decimal --> Hexadecimal) (NETAPP comment) 
3. [modify] change 3.3V battery get sensor reading interval time to 1 hour
4. [change] change clear CMOS SEL severity from warning to info
5. [Change] follow S5BV_FSC_Table R11, change T4 offset from 0 to 10 
6. [change] change fan table for sku 0~7
7. [Update] update worst card list to R42

[Bug Fixed]:
S5Bx/S5Sx:
1. [Fix] Debug the issue that the web page didn't show the checkbox of "Sensor Events" if the "Sensor Events" option is choosen.
2. [Fix] Debug the issue #313867, #313634, #312146.
3. [Fix] Fix the remind message of password's string typo.(e-track#315415)
4. [Fix] The note of BMC WebUI 'Firmware Update' page is incorrect.#265335
5. [Fix] EIP 334620 NTP time sync not workable after BMC initial done
6. [Fix] [Fix] sync svn 88029 to fix sdr sync bug. #318993 #318869
7. [Fix] Fix #313400 , webui can't filter "BMC FW Health" type.
8. [Fix] remove unmask psu alert function to fix #308216
9. [Fix] fix #288868, fine tune power on timing.
10.[Fix] fix #308961

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v4.97.00
==========================================================================
Version: 4.96.00
Release Date: 2020.02.13
Code Based: 4.90

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.22)

[Firmware Images]:
1. rom.ima with checksum          :  E7A21A8D 
2. rom.ima with MD5 checksum      :  BCFDC3292F6F1E75954F3DC7397D1086 
3. rom.ima_enc with MD5 checksum  :  EAE283DB8CEA465DD05717C6ECF096C3

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. update worst card list to v40
2. [Add] Sync initial Repeater with paramaters on each timing(Power on, Reset, etc).
3. [Add] updtae GPU AVL table to add NVidia RTX6000 passive, RTX8000 passive, V100S
4. [Modify] Modify S7D NM Status Sensor's config. Change GID from 0x602C to 0x0020.
5. [Modify] Modify S7D GPU temp sensor's name.

[Bug Fixed]:
S5Bx/S5Sx:
1. QCT:Fix duplicate IPv6 Dynamic Router
2. sync S5Y, Modify the PEF function to avoid BMC reboot.
3. [Fix] fix #256780, modify password rule.
4. [Fix] 1. Fix eTrack #294031, there is no "SKU-Project-Unavailability. Assert" event log if MB fru is NULL. (not workaround)
5. [Fix] Fix eTrack# 308238, edit the sel string.
6. [Fix] fix E-track #308785, when SUT is without HBA card, error message will not pop up.
7. [Fix] S7D PSU mode should restore to balance load after restore default.(etrack#309954)
8. [Fix]Fix S5D/S7D watchdog timeout during AC cycle. S5D/S7D does not need to mask PSU alert.(e-track#311342)


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v4.96.00
==========================================================================
Version: 4.96.00
Release Date: 2020.01.08
Code Based: 4.90

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5


[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          :  F1B3A7CF 
2. rom.ima with MD5 checksum      :  73B73698D42BBBE2D66F2246D497AB8E 
3. rom.ima_enc with MD5 checksum  :  1B6D4EF6610764079C99C1722F559469

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. [Add] For ipmi carsh issue during AC cycle, Disable QuantaGetSensor info cmd.
2. [Modify][AC lost]Sync other project, fix watchdog timeout. Forzen(disable) the SPI Flash while AC lost, and dis-Forzen the SPI Flash while quick AC lost recovery.  
	Fix the failure while suddenly AC lost at reading/writing SPI.
	
[Bug Fixed]:
S5Bx/S5Sx:
1. [Fix] #309466 add new user account event
2. [Fix] #309473, sel log would not show delete user event.


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v4.95.00
==========================================================================
Version: 4.95.00
Release Date: 2019.12.27
Code Base: 4.90

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5
Api Version: 2.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          :   E79FF7F2
2. rom.ima with MD5 checksum      :   5DF6688FF84A9D1EE3DFCAEC51F6B7DC
3. rom.ima_enc with MD5 checksum  :   5026BFD9C2F4C366E1B9C4AC28A0AF82

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. [Add] 1. Add Oem Command: Get CA Law Status (0x36 0x69).

[Bug Fixed]:
S5Bx/S5Sx:
1. [Fix] Fix to align H5Viewer KVM canvas and cursor canvas propery. Root cause: CSS property to make canvas (KVM and cursor) overlap each other isn't working properly in the chrome browser.
2. [Fix] Fixed H5Viewer canvas alignement on first launch (no video in host)


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v4.94.00
==========================================================================
Version: 4.94.00
Release Date: 2019.12.24
Code Base: 4.90

AMI Subversion Revision: AMI SPX RR11.5
DMTF Redfish Specification Vision: 1.5
Api Version: 2.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          :   E7A088D7
2. rom.ima with MD5 checksum      :   8B959EE4A12C35E444F1F4942E358860
3. rom.ima_enc with MD5 checksum  :   D21C4C6A2CC482EC4C93C9FA15DBAB5D

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. [add] support X710 fru format , need pass through BIOS post start to recognize X710 and recall PDKFRU init again
2. [Fix] Fix MF5A wrong Fan present log.
3. [Modify] sync other project svn#87442: cancel the mutex acquire and release, add HAL_ERR_READ for retry while fail.
	Fix watchdog timeout at pwoer reset stress test.
	Can also reference other project svn#86864 #87440
4. [Add] 1. Mask PSU all alert for platform include CMC.

[Bug Fixed]:
S5Bx/S5Sx:
1. [fix] radius login web ui fail (password format error, EIP 468173)
2. [Fix] Fix DIMM initialization fail and DIMM configuration problem's event log string. Based on SPX_EvtTbl_4.48(etrack#283005)
3. [Fix] Debug the issue #265716. Issue: Input invalid characters (a character)to the Country on Generate SSL Certificate page cannot pop-up error message and Update SSL Certificate will fail.
4. [Fix] fix #306759, Set change pwd length maxmum to 16 characters when user first login. 
5. [Fix] fix redfish problems of Ca- LAW
6. [Fix] fix #306703 : user id will not display in sel log  when user change pwd in first login.
7. Fix factory recovery command failed in the in-band case.
8. [fix] EIP 506236 web ui can't work after setting different subnet for default gateway
9. [fix] Temp_SSD_11 severity is info, because its sensor number conflict to ME sensor(0x3b) , change sensor number to 0x80
10. [fix] S5B/S5S sometime system continuous record CATERR sel at system DC off
11. [Fix] Debug the issue #265773. Issue: Invalid IPv6 will be saved successfully on WebUI.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
2. After Update BMC FW from 4.73.00 to 4.74.00(include later version) or from 4.74.00 to 4.73.00 (include older version), some SEL log data will be abnormal.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 



==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.93.00
==========================================================================
Version: 4.93.00
Release Date: 2019.12.02
Code Base: 4.90

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.5

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          :   E7B0FEEB
2. rom.ima with MD5 checksum      :   9D6DEC8ECA9E957D2801D390F2C3FAED
3. rom.ima_enc with MD5 checksum  :   399E766CD02117BD5934A4640F711412

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. update worst card tble to R37.1
2. [Fix]Toshiba NVMe SSD always keeps 0 degree on S7D (etrack#300331).
3. [update] update S5T,S5L: BAT_3V threshold 3.510/2.205V
4. [Modify] Modfiy the severity of ECC error log from critical to warning.
5. [Add] change the IERR peci command, add CrashDump and global reset after IERR trigger, add peci command retry function. 
6. [sync] #82420 fix image upload timeout is shorter than user's network condition and the process bar on webui will switch each processing quickly then the bar will look strangely.
7. [Debug] Debug the issue #301951. eTrack #301951: The item of ''Read-Only Community String'' in SNMP page should not allow user input space and save successfully.
8. [Modify] change the peci command type from peciRawCmd to wrPkgConfig
9. [Add] 1. Mask PSU all alert.
10. [Merge] Merge GPU/PCIE setting and fan table from 4.76
11. [ADD] add feature "first_login_change_password_support" for CA law, modify fw update oob script file for password parameter 2 
12. [Add] S7D patch for fixing PCIe error log's slot number.(e-track 296553)


[Bug Fixed]:
S5Bx/S5Sx:
1. [Fix] Sync svn CMCC/candidate #80737, 1. [Fix] BMC will reset automatically after dc cycle for 60HR.
2. [Fix] Sync 94.74.22/86580 [Add] 1. Add raidmngr-init flag for checking raid manager complete. 2. remove AMI debug messages.
3. [Fix] Sync 94.74.22/86596 [Fixed] Fix the componet manager isn't ran after bmc watch dog reset.
4. [Fix] Sync 94.74.22/86615 [Fixed] Fix the componet manager isn't ran after bmc watch dog reset.(Add COMP_First_boot for recognizing first boot.)
5. [Fix] Sync 94.74.22/86625 [Fixed] Fix the componet manager isn't ran after bmc watch dog reset.(Add COMP_First_boot for recognizing first boot/ipmistack restart.)
6. [Fix]Fix BMC record wrong Fan Present log when SUT run AC power cycle. etrack#293400
7. [fix] fix system error message when send ipmi command to get raid card configuration
8. [Fix] For #296147, ipmi command can set Vlan id = 1, not follow QCT Spec.
10. [fix] block bmc transfer data to cmc while update cmc to avoid cmc update fail 
11. [Fix] Debug the issue #301014. Issue: Fill out the invalid email on the ''Sender Email ID'' field won't be saved but it will show ''true'' when click save button.
12. [Fixed] Fix SEL record AC lost when BMC triggered watchdog timeout.
13. [fix] EIP 502465 IPV6 mac addr will lost sometime when AC cycle stress


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.92.00
==========================================================================
Version: 4.92.00
Release Date: 2019.09.18
Code Base: 4.76

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.5

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          :  E9E5F170
2. rom.ima with MD5 checksum      :  9845FBDAF7A2216EBF95D2CBA82FDD6F
3. rom.ima_enc with MD5 checksum  :  805CABB6FB8988D3C87966739207C509

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. add oem command: get/set dimm date code and location.

[Bug Fixed]:
S5Bx/S5Sx:

 
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 


==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.91.00
==========================================================================
Version: 4.91.00
Release Date: 2019.09.12
Code Base: 4.76

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.5

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : E7E1D158
2. rom.ima with MD5 checksum      : 266E2E2F6BB7328A850793B772AFE05B
3. rom.ima_enc with MD5 checksum  : BEFD1CEC7E296455B319C1DAC3D1F2DC

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. Refish update to v1.5 and enable RSD 2.4
2. Modify Volt_P3V_BAT threshold 3.507V / 2.205V 

[Bug Fixed]:
S5Bx/S5Sx:

 
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.90.00
==========================================================================
Version: 4.90.00
Release Date: 2019.08.29
Code Base: 4.76

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.5

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : E9932F37 
2. rom.ima with MD5 checksum      : 4E1B229A1655090044573C3639A5E2E7 
3. rom.ima_enc with MD5 checksum  : 660C3F8D53423A707354B03C1B886C8A 

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
1. Refish update to v1.5
2. Support to read temp from Intel card Darby Creek 

[Bug Fixed]:
S5Bx/S5Sx:
 1. fix #292393 sel log can not record account change.
 2. modify design to fix #292162.
 3. fix #288607 for snmp alert issue.
 4. fix sensor sometimes can not show value. 
 
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can not downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.76.00
==========================================================================
Version: 4.76.00
Release Date: 2019.07.31
Code Base: 4.70

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : EF57E235 
2. rom.ima with MD5 checksum      : 7428D2981AAD6961A4B665BEDC0F1B06 
3. rom.ima_enc with MD5 checksum  : 86B17D10B0FE8DDE9278ABA62E7A032C 

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
[Change] Reverse Redfish version to 1.1


[Bug Fixed]:
S5Bx/S5Sx:


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.75.00
==========================================================================
Version: 4.75.00
Release Date: 2019.07.31
Code Base: 4.70

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          :  E99AFD99 
2. rom.ima with MD5 checksum      :  AFDBBAB395992CE0B2473DDCAAD1487C 
3. rom.ima_enc with MD5 checksum  :  0E30CF7576151FA03E0B6683ED6025AD 

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:
[Add] Add Intel PCIE Card VCA2 information and modify PCIE card weight for S5BV sku 8~9.
[Add] Nvidia RTX 6000,8000 information into available list
[Add] Update Redfish 1.5
[Add] Update worstcard list to R35

[Bug Fixed]:
S5Bx/S5Sx:
[Fix] Redfish data of CPU lack the data of Max Speed.#267229, #279396
[Fix] NvME SSD Intel P4800x always keep 22 degree. #279874
[Fix] UpdateService FlashProgress didn't be updated. #280277
[Fix] WebUI will pop-up "password do not match". #280298
[Fix] Raise sensor thermal max value to 0x5e.#283948
[Fix] Remove gpgpu sensors from sensor lost list.#283996
[Fix] Fix set load default failure issue.
[Fix] Plug 4 pieces of RTX series but GPU sensor only read 3 pieces problem  
[Fix] GPU sensor will be -1 when the temperature is over the default value 

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.74.00
==========================================================================
Version: 4.74.00
Release Date: 2019.05.28
Code Base: 4.70

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          :   EF52AC86
2. rom.ima with MD5 checksum      :   F2EE2A8131E434D77011758499BD8D75
3. rom.ima_enc with MD5 checksum  :   05F22B7BE4A69A543336E0A28303612B

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03
SKU80~82: R20
SKU83~87: V12

[Change/Add]: 
S5Bx/S5Sx:

[add] add oem cmd set/get CPU info trouble mode status

[Bug Fixed]:
S5Bx/S5Sx:

N/A

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
        
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.73.00
==========================================================================
Version: 4.73.00
Release Date: 2019.04.15
Code Base: 4.70

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : EF794802
2. rom.ima with MD5 checksum      : E02B1AC380E8158BB287228A6FB069E7
3. rom.ima_enc with MD5 checksum  : 2FB8FCF876E53AFA2C2A9544C2E17FD6

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:

N/A

[Bug Fixed]:
S5Bx/S5Sx:

[Fix] 1. Fix After ISO Image mount by UEFI mode, after random period of time, "Remote Media" button loss is occurred and browser crashed, BMC lost connection.
[Fix] 2. Web ui will auto reload after lost connection 20 times and makes RKVM lost its mounted iso file (remote install fail).
[Fix] 3. Cdrom keep alive packet will lost sometime and will close RKVM automatically.
[Fix] 4. IP source would not be changed throught IPMI command.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.72.00
==========================================================================
Version: 4.72.00
Release Date: 2019.03.14
Code Base: 4.70

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : EF72ABE5
2. rom.ima with MD5 checksum      : 136C4B3808547767E32C3BD515F5ECB1
3. rom.ima_enc with MD5 checksum  : B452E07BB8AA7B9EE5315F19D0504D85

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:
1.add feature_security_enhancement_support config for user account security enhancement function


[Bug Fixed]:
S5Bx/S5Sx:
1.S5B redfish : fix entrytype of SEL according to redfish SPEC
2.S5B redfish : track 263009
3.fix preserve firmware update cause redfish restore to default password
4.fix linux inband update fail



[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.71.00
==========================================================================
Version: 4.71.00
Release Date: 2019.01.17
Code Base: 4.70

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : EF4BBFFD
2. rom.ima with MD5 checksum      : 3BD2CCB56D9D3717EC326689B8E73BD4
3. rom.ima_enc with MD5 checksum  : 2E828DA7D62EDFC3DABC010816C51DD6

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:
1.Add Redfish usb0 addr/mask/gatway patch method.

[Bug Fixed]:
S5Bx/S5Sx:
1.Remove USB lost recovery solution to add timer to enable/disable hub/device.
2.Fix Redfish force static to dhcp4.
3.Fix disable S5B/S5BQ/S5S BMC debug console capture feature and kill all /conf process while during yafuflash FW update because it will cause BMC FW crash.
4.Fix Redfish Quanta syntax error.
5.Fix Redifsh Description error in curl response data.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.70.00
==========================================================================
Version: 4.70.00
Release Date: 2018.11.30
Code Base: 4.70

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : EF565DEC
2. rom.ima with MD5 checksum      : 1AD3842A415EBB45B360AED095481155
3. rom.ima_enc with MD5 checksum  : 7743BA5F0F8B025D6CE76B566B353736

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Change username could make user login webUI without first login
2. Add the sync process for lan settings
3. Add new feature behavior for "When user2 login solssh over smash, the connection of solssh for user1 is disconnected"
4. Upgrade storelib from MR 7.2 to 7.6.
[Bug Fixed]:
S5Bx/S5Sx:
1. Fix the problem that hostname command fail to execute 
2. Add the function of skipping "Force Change Password".
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.55.00
==========================================================================
Version: 4.55.00
Release Date: 2018.11.20
Code Base: 4.50

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : EFF4ED70
2. rom.ima with MD5 checksum      : 75DB00C283A59A05C4B8F440EF2B52E3
3. rom.ima_enc with MD5 checksum  : 290F10D5A83F9D84FBDAF14646B4E18B

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Add the function of skipping "Force Change Password".
[Bug Fixed]:
S5Bx/S5Sx:
N/A

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.54.00
==========================================================================
Version: 4.54.00
Release Date: 2018.11.02
Code Base: 4.50

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : EFF248F9
2. rom.ima with MD5 checksum      : CAE878C46875C11BD46BF7E8BBAA0FC5
3. rom.ima_enc with MD5 checksum  : D7DF512C9B4533D2CFFE4668DEBCA91D

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Update worst card list table to R25.
2. Add ncsi failover(like X540) solution.

[Bug Fixed]:
S5Bx/S5Sx:
1. Fix componet manager is stuck when run workarround method.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.53.00
==========================================================================
Version: 4.53.00
Release Date: 2018.10.25
Code Base: 4.50

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : EFE90E3E
2. rom.ima with MD5 checksum      : 4666FA32F3D94D3195A565009ADDA792
3. rom.ima_enc with MD5 checksum  : 51F4AC4FE357808FCB20762A6ED1BDED

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Support discovery all Redfish Resource.
2. Support `SlotNumber`, `Description` in PCIeDevices in redfish.`SlotNumber` is based on the SMBIOS type 9 value. According to slotnumber, no matter which riser card in use, we can know the CPU0 or CPU1 that the PCIeDevice belongs to. And `Description` information is generated by VID/DID
3. Support Post Status in redfish to make sure redfish receives NIC, Storage information.
4. Support Hard Drive Physical BlockSize in redfish.
5. Support Lit Physical Hard Drive indicateLED in redfish.
[Bug Fixed]:
S5Bx/S5Sx:
1. Fix raid can't get infromation when do dc cycle and ac cycle
2. Fix Fan duty will stay in wrong duty when the temperature is stay low.
3. Fix enable/disalbe smash command can't work normally.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.52.00
==========================================================================
Version: 4.52.00 
Release Date: 2018.10.05
Code Base: 4.50

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F02A5C82
2. rom.ima with MD5 checksum      : 728150A00079EB538C659E384B343379
3. rom.ima_enc with MD5 checksum  : 02EE4264E7827E7087182373C9AF570A

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Improve the tolerance for RKVM connections.
2. Fix IP Address source of WebUI not sync with Redfish.
3. Modify ssh to let enable/disalbe smash command work.
[Bug Fixed]:
S5Bx/S5Sx:
1. The format of OriginOfCondition of event of EventService didn't match SPEC of redfish schema.
2. Add the attribute "MemberId" back to the event.
3. Fix IP Address source of WebUI not sync with Redfish.
4. "Fix IP Address source of WebUI not sync with Redfish"
5. Fix RKVM of H5Viewer for media can't reconnect bmc
6. [246622]BMC password can be set less than 8 bytes while first time login.
7. [248268]When update BMC with ima file on BMC WebUI, the warning message will show the incorrect word.(Should be ima_enc)
8. [248270]There's no hint string about JAVA rKVM not support Java 9 and Java 10 when mouse hover on ''Launch KVM(Java)'' 
9. [248907]After selecting non-enc IMA file to upload ,the WebUI display tip string ''Invalid Firmware image.Only IMA file is support'' not correct 
10.[248748]The string format of BMC WebUI device information are not matched with each row
11.[248771]The description of ''Sign out'' button on BMC WebUI is incorrect. The description is ''The Admin profile can be viewed.'' 
12.[248558]When connect BMC 4.51.00 WebUI with http connection, BMC will not redirect to https connection. Mismatch to BMC standard SPEC v2 42x.(BMC_FW_DesignStandard_For_AST2X00Spec v2 42x)

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.51.00
==========================================================================
Version: 4.51.00 
Release Date: 2018.08.09
Code Base: 4.50

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F0316F2B
2. rom.ima with MD5 checksum      : 23B7A056DE7142FC3A9E50341EB06D4F
3. rom.ima_enc with MD5 checksum  : BAB388E7F950EEBDCC143CDD3A99CC72

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
N/A
[Bug Fixed]:
S5Bx/S5Sx:
1. Fix BMC can't be updated via inband way.
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.50.00
==========================================================================
Version: 4.50.00 
Release Date: 2018.08.02
Code Base: 4.20

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F02FB786
2. rom.ima with MD5 checksum      : 70914CB5A4A8DC2BD47FD5EF22E35B17
3. rom.ima_enc with MD5 checksum  : 9B69F27AFD5BEABFD2C7FC568B6E25B8

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Update the worst card list R23. 
[Bug Fixed]:
S5Bx/S5Sx:
N/A
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.24.00
==========================================================================
Version: 4.24.00 
Release Date: 2018.07.19
Code Base: 4.20

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F03D3C3A
2. rom.ima with MD5 checksum      : F3386D89ECD2444535BD86B372AC31D7
3. rom.ima_enc with MD5 checksum  : 9634923E52A30C0F0D25D77380B67025

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Change codebase Rev access method. 
2. Improve the efficiency of raid process.
3. Change the common key to be the same with all project when updating the BIOS.
[Bug Fixed]:
S5Bx/S5Sx:
1. Fix raid process will crash when do dc cycle.
2. Increase retry times at RKVM in video transmission.
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	2. User can\92t downgrade the BMC with preserve.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.23.00
==========================================================================
Version: 4.23.00 
Release Date: 2018.06.19
Code Base: 4.20

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F2EC179F
2. rom.ima with MD5 checksum      : 120FD69781F8F79DFDDB7B55C7459850
3. rom.ima_enc with MD5 checksum  : 6412BFB1CD993A21FEA663E102741B32

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
N/A
[Bug Fixed]:
S5Bx/S5Sx:
1. Fix RKVM will be interrupted unnormally when doing dc cycle with share nic.
2. Fix Code base number will disappear after several AC Cycle test. 
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.22.00
==========================================================================
Version: 4.22.00 
Release Date: 2018.05.11

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F31F82AE
2. rom.ima with MD5 checksum      : 0AB9A5A9E3B460DAAC74933B688736BD
3. rom.ima_enc with MD5 checksum  : FC3414A2F85CE9A99912305C1ACDE1F3

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
N/A
[Bug Fixed]:
S5Bx/S5Sx:
1. [200746] Move mouse cursor to HTML RKVM buttons, there has no hint to inform user the usage of RKVM buttons.
2. Fix serial number shows different between msm tool and storelib.
3. Fix raid card can't be read for ROC tmp
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.21.00
==========================================================================
Version: 4.21.00 
Release Date: 2018.04.20

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F37BED78
2. rom.ima with MD5 checksum      : 00E3A95580D02A2A0A8555D4D0A60823
3. rom.ima_enc with MD5 checksum  : C30F368C4B4D81DFA42D9BB3A3E7AD62

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Add the signed process when you update cpld img or bios img
2. Add code base number feature into bmc
3. Add account security policy
[Bug Fixed]:
S5Bx/S5Sx:
1. Fix raid card can't be read for ROC tmp
2. Fix the information of read/write policy isn't synced between bios and webui. 
3. Fix the username and passwrod is invalid in refish sometimes.
4. [222856] [S5B][NSN sync]WebUI SMTP server address will change after BMC update complete via WebUI. (used preserve configuration)
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v4.20.00
==========================================================================
Version: 4.20.00 
Release Date: 2018.03.30

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F3CCBF9B
2. rom.ima with MD5 checksum      : 2A3CF6E804C3F4A20860A80DEA1FF388
3. rom.ima_enc with MD5 checksum  : 2AE3FCCC8E96CE66A4C42449D871F125

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
N/A
[Bug Fixed]:
S5Bx/S5Sx:
1. [221481][BMC Q1][REG45]HTML5 will hang or disconnect when during FIO(Dedicated-NIC).
2. [227746] [BMC_Q1_Block]HTML5's time would delay(Firefox)(BMC 3.82.00).
3. [200746] Move mouse cursor to HTML RKVM buttons, there has no hint to inform user the usage of RKVM buttons.
4. [222856] [S5B][NSN sync]WebUI SMTP server address will change after BMC update complete via WebUI. (used preserve configuration)
5. [229474] [OOB 2294][S5B REG83][Customize FW For SFC] RKVM will popup ''INVALID WEB SESSION COOKIE'' and disconnect during the DC cycling test.(Mount the USB with RKVM)
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v3.89.00
==========================================================================
Version: 3.89.00 
Code Base: 3.85.00
Release Date: 2018.05.07

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.2

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F3FCC367
2. rom.ima with MD5 checksum      : 6120259695DDCAA231010F3561DDE5EB
3. rom.ima_enc with MD5 checksum  : E94D56B68ACFAD7584B8E97594F1045C

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Add support for Micron NMVE SSD temperature monitor.
2. [Redfish] Add MircocodeInfo for ProcessorId.

[Bug Fixed]:
S5Bx/S5Sx:
1. Fix BMC will crash when do DC cycle test for several times.
2. Fix the information of read/write policy isn't sync between BIOS and WebUI.
3. Fix SASIT can't be read successfully.
4. Fix serial number shows differently between MSM tool and storelib.
5. Fix WebUI fail to launch after NASM uploading SSL certificate.
6. [Redfish] Fix UpdateService failed to preserve configurations.
7. [Redfish] Fix DateTime not sync with BMC system.
8. [Redfish] Fix EventService didn't check EventType before send events.
7. [Redfish] show null if sensor threshold value not define.


[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v3.88.00
==========================================================================
Version: 3.88.00 
Release Date: 2018.04.19

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.2

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F4089944
2. rom.ima with MD5 checksum      : F4A00A9BB0BED8BD85A9FD15899BBB29
3. rom.ima_enc with MD5 checksum  : E836C07AE6E21CD25716F004141ED0D7

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
N/A
[Bug Fixed]:
S5Bx/S5Sx:
1. Fix raid card can't read for ROC temperature.
2. Fix the information of read/write policy isn't sync between BIOS and WebUI.
3. [222203] Get unexpected RoleID in response data when create new account.  
4. [235290] BMC basic auth becomes malfunction in some case.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B/S5S serials AST2500(A2) BMC FW Release v3.87.00
==========================================================================
Version: 3.87.00 
Release Date: 2018.04.10

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.2

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F40D4B20
2. rom.ima with MD5 checksum      : 32E44BFFA017C9CF46E00E770CE0E982
3. rom.ima_enc with MD5 checksum  : AF45D5E3CB641A46C5BF4D4CA7E8F948

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
N/A
[Bug Fixed]:
S5Bx/S5Sx:
1. Fix Redfish syncing process error problem.
2. Fix the username and passwrod is invalid in refish sometimes.
3. Fix VNC will interrupt when do power cycle in 48 hours.
4. [208229]WebUI RAID management BBU information #1.Type info mismatch with MSM #2.Current unit shall be mA.  
5. [236184] [S5S] [ebay] [REG58] BMC version is not correct via smash.(Show3.86.85030a)
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
		
==========================================================================
        S5B/S5S series AST2500(A2) BMC FW Release v3.86.00
==========================================================================
Version: 3.86.00 
Release Date: 2018.03.30

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.21)

[Firmware Images]:
1. rom.ima with checksum          : F40B0A03
2. rom.ima with MD5 checksum      : 536F092B9E64EC50765E542EFA17FEFF
3. rom.ima_enc with MD5 checksum  : F3B6DBC40853C58DBDEC709FC2E3FD89

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx/S5Sx:	
1. Update Yafu flash tool to version 4.16.21.
2. Add get CM PSU data for redfish PSU reporting.
3. Redfish block login WebUI when UpdateService flash FW.
4. Redfish fix s5b UpdateService flash BMC image fail
[Bug Fixed]:
S5Bx/S5Sx:
1. [234011][SFC][REG95]Didn't insert PSU1, but SNMP's temperatureDeviceInfoStatus still display ''ok'', and temperatureDeviceReadings is ''0''.

[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 


==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.85.00
==========================================================================
Version: 3.85.00 
Release Date: 2018.03.05

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : F48062F4
2. rom.ima with MD5 checksum      : EB1EC0F09230F2D0EC7925CE8F1DBCEA
3. rom.ima_enc with MD5 checksum  : 0FDC988AF19CB861249EC796D3F27116

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx:	
1. Change raid information from raid management and SASIT management.
2. Remove workarround method for unworkable network in share nic mode. 
[Bug Fixed]:
S5Bx:
1. [230361] [REG87] SEL record "BIOS image update from 3A10.04 to 3A10.Q0 success" when we update BIOS 3A10.04 to 3A10.Q04
2. [200698] Connect HTML5 RKVM and press ''ALT+TAB'' to switch to other task, found SUT local keybaord cannot work properly.
3. [214715][BMC Q4 Block][REG33]after Build RAID 0 , WebUI would show error message about code 11259
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.84.00
==========================================================================
Version: 3.84.00 
Release Date: 2018.02.09

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : F49B0430
2. rom.ima with MD5 checksum      : F512FC9DB7606FCA127F9D3E8D204E3E
3. rom.ima_enc with MD5 checksum  : DEC371BF0C85AD0FDEF9C2229F984EF6

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx:	
1. Add default setting of hostname register method for customer CTO
2. Add default setting of port blocking for Salesforce. 
3. Add set PCIE info to JG3 for S5B and S5S project
[Bug Fixed]:
S5Bx:
1. Fix RKVM disconnect easily when using HTML5
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.83.00
==========================================================================
Version: 3.83.00 
Release Date: 2018.01.31

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : F49FDCC5
2. rom.ima with MD5 checksum      : F93482DDF703FD3EB5E3117AA192E2EC
3. rom.ima_enc with MD5 checksum  : E322691D5D6237EAF2E66153DC05FBAF

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx:	
1. Disable SMI feature.
2. Add switch lock mechanism for GPU,retimer, and raid card polling task.
3. Add funtions to avoid firewall rule could be repeated on port setings.
4. Add ddns feature.
5. Change Rpu/Rpd value to 0x1e6e0240.
[Bug Fixed]:
S5Bx:
1. [222640] Unable to know which retimer cable lose if any retimer cable lost link while Host port is still link up. (e.g. Host port bandwidth drop from x16 to x8 but no ''SEL log'' record which retimer cable lost.)
2. [222514][JG3R] Unable to know if any MiniSAS cable lost link while Host port is still link up. (e.g. Host port bandwidth drop from x16 to x8 but no ''syslog'' record which MiniSAS cable lost)
3. [225568][MF5A][EVT] Redundancy mode can't change when system power on with 1 PSU is AC source and 1 PSU is DC source.
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.82.00
==========================================================================
Version: 3.82.00 
Release Date: 2018.01.18

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : F77EAC79
2. rom.ima with MD5 checksum      : 0037C30C404DAE82493BCAA93701F28F
3. rom.ima_enc with MD5 checksum  : F143812E54A71092BEACBB9146B8B2DE

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v03

[Change/Add]: 
S5Bx:	
1. Disable BMC auto recovery function.
[Bug Fixed]:
S5Bx:
1. [210824] S5BQ 3540 SKU(Expander) system via IPMI command will get backplane FW version is null.
2. [214097] [S5B_WebUI_3224/3216] SAS IT management NVDATA version did not match with actual version.
3. [210355] WebUI RAID Management ''Physical Device Information'' page has no icons to ''Remove'' Dedicated Hot Spare and ''Stop'' Locate Drives.
4. [199979] [3540] 9361-8i/9380-8E UEFI Ver/Expander Ver/ CPLD Ver/Expander Temp value show N/A on RAID Controller Information of WEBUI
5. [206473] WebUI ''Device Information'' has no Expander FW and PSU FW information. (S2P pass)
6. [201682] [PVT] QS-3108A-8i RAID Controller Information is incomplete on RAID management of WebUI Settings.
7. [214681] [BMC Q4 Block][REG33]No Stop located LED button in RAID Management after start locate it.
8. [200661] [DVT][WebUI] There is no Stop located LED button in RAID Management / SAS IT Management tab and is won't stop locate hard drive if user start locate it.
9. [222448] [S5B][NSN sync.]S5B/S5BQ login to BMC SMASH is slow, it takes around 30 seconds to get the SMASH prompt. (S2PH takes less than 3 sec to access the SMASH)
10.[222435] [S5B][NSN sync.]Execute the command ''show /sp.BMCMAC'' in SMASH interface, it will returns all properties, not just the selected.
11.[222119] [S5BV_PVT]It will close the window directly when log in SMASH. (BMC FW :3.69)
[Known issue]: 
1. After Update BMC FW from 3.81.00 to 3.82.00, you have to wait arround 8 minutes to login BMC web login page because of enabling auto recovery. This issue only happened in BMC FW 3.81.00.
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.81.00
==========================================================================
Version: 3.81.00 
Release Date: 2018.01.08

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : 0003E695
2. rom.ima with MD5 checksum      : B38E1D90BDBABF127BB159D3C5C7F452
3. rom.ima_enc with MD5 checksum  : 35DE92AE4CEF22201C3A63AA7A6A7363

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Change the title of RKVM from ip to hostname. 
2. S5S support JG3 re-timer card.
[Bug Fixed]:
S5Bx:
1. [200746] Move mouse cursor to HTML RKVM buttons, there has no hint to inform user the usage of RKVM buttons.
2. [213832] [BIOS Q4 Block-REG32]SEL record ''BIOS image update from V.3A10 to V.3A10 success'' when we update BIOS 3A10 to 3A10.01
3. [213294] [Block Q: 2017-Q3]SEL record ''BIOS image update from V.3A10 to V.3A10 success'' when we update BIOS 3A10 to 3A10.01
4. [214097] [S5B_WebUI_3224/3216] SAS IT management NVDATA version did not match with actual version.
5. [210824] S5BQ 3540 SKU(Expander) system via IPMI command will get backplane FW version is null.
6. [206473] WebUI ''Device Information'' has no Expander FW and PSU FW information. (S2P pass)
[Known issue]: 
N/A
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.80.00
==========================================================================
Version: 3.80.00 
Release Date: 2017.12.05

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : 00C9987B
2. rom.ima with MD5 checksum      : 8165289FFE19115F94A4D0CA8558279D
3. rom.ima_enc with MD5 checksum  : 3B02B874FCBDF69D6022557C4BCD0237

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:
S5Bx:
1. Add Html5 feature for RKVM
2. Add Auto BMC recovery feature from uboot. 
3. Update fan table for s5bv R03.
[Bug Fixed]:
N/A
[Known issue]: 
N/A
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.67.00
==========================================================================
Version: 3.67.00 
Release Date: 2017.11.28

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : 00C96608
2. rom.ima with MD5 checksum      : 7623BA25282DA3D2BEE79C77B6549755
3. rom.ima_enc with MD5 checksum  : CED3495109941696A3B6C0BBB179074F

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
N/A
[Bug Fixed]:
S5Bx:
1. Fix USB signal can't be passed to OS. 
2. Modify the workarround method of SOL may disconnect from bmc and fix side effect with sol cmd "looptest".
[Known issue]: 
N/A
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.66.00
==========================================================================
Version: 3.66.00 
Release Date: 2017.11.23

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : 00CA2B2E
2. rom.ima with MD5 checksum      : 46B08EFAA4D5E563BAB535ABCDA34D5B
3. rom.ima_enc with MD5 checksum  : DA36309359E57EA08A41FB9D5BF236D0

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Update Worst card table to R15.
[Bug Fixed]:
S5Bx:
1. [211489] BMC will close SOL session when running warmboot cycle.
2. [214102] The SOL Session closed by BMC occurs when execute the Multi -Session Test-Share NIC test
3. [214093] The SOL session closed by BMC occurs when execute the BMC Multi-Session test(Dedicated-NIC).
4. AC cycle BMC will reset.
[Known issue]: 
N/A
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.65.00
==========================================================================
Version: 3.65.00 
Release Date: 2017.11.17

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : 00E16B84
2. rom.ima with MD5 checksum      : 6E7F63CF633423C6A2C41CD929C8E29F
3. rom.ima_enc with MD5 checksum  : 38B5FF42E4041FAEEF2FE5FBC4730331

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Update platform.S to V18.
[Bug Fixed]:
S5Bx:
1. [213832] SEL record ''BIOS image update from V.3A10 to V.3A10 success'' when we update BIOS 3A10 to 3A10.01
[Known issue]: 
N/A
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.64.00
==========================================================================
Version: 3.64.00 
Release Date: 2017.11.10

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : 07C7B3FB
2. rom.ima with MD5 checksum      : C77D79DECE74159AEC646A3C6AADCFE2
3. rom.ima_enc with MD5 checksum  : 79EB15F103386EF3A2050CFB841DCA2B

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
N/A
[Bug Fixed]:
S5Bx:
1. [213747] Firmware Build Time does not match to Release note.
2. [214851]	WebUI does not show message about ''Host in Power Down State'' when SUT is poweroff
3. [215509] There have an error message in ''SAS IT Management'' options.
4. [214203]	WebUI is easily session expired when click Setting of RAID Management information page.
5. [214101] SAS IT Management cannot detect any HDD under Physical Device page and the Topology Information do not correct.
6. [210377] WebUI is easily session expired when click Removal icon in RAID Management ''Physical Device Information'' page.
7. [210359] WebUI Error message shows after add/remove Global Hot Spare in RAID Management ''Physical Device Information'' page.
8. [214716] On  Physical Device Information\Storage summary page are empty and would show error message with 9380-8E card
9. [208222] WebUI RAID Management ''Event Log'' page shows ''No Records'' but use storcli tool can see many events logged.
10.[208218] Check WebUI ''RAID Controller Information'' when system is power off, the pop-out message doesn't match with ESMS spec v1.24 definition.
11.[208974] Prepare removal disk can be successful, but WebUI has been Session Expired after plug out disk and click Undo and got error messages ''Error in setting Prepare for Removal configurations [code:11256]'' after set RAID Management.
12.[208122] WebUI is easily session expired when click RAID Management ''Logical Device Information'' page.
13.[201726] Web-UI ''RAID Management-Logical Device Information-Create virtual device''should not have RAID1E of QS3108A-8I(QS3108A-8I not support RAID_1E)
14.[208810] BMC WebUI RKVM cannot mount USB key(2.0/3.0) via USB port 3.0. (Used the USB port 2.0 passed and passed before).
15.[208214] WebUI pop-out error message when select RAID volumn operation in ''Logical Device Information'' page.
[Known issue]: 
N/A
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.63.00
==========================================================================
Version: 3.63.00 
Release Date: 2017.10.31

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.17)

[Firmware Images]:
1. rom.ima with checksum          : 086B3A4F
2. rom.ima with MD5 checksum      : 825C8471D07C94835634B1A8972BC757
3. rom.ima_enc with MD5 checksum  : 5D74114E47D677627AA6942573D51A4C

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Update Yafuflash to version 4.16.17.
2. QSM Discovery by Redfish.
3. QSM Redifsh performance improvement for single session.
4. QSM Certificate update.
[Bug Fixed]:
S5Bx:
1. [212127] WebUI SAS Physical Device Information of QS 3008 IT got wrong temperature status 255.
2. [208406] Check 9361-16i RAID volumn in WebUI ''Logical Device Information'' page, some information are incorrect.
3. [210377] WebUI is easily session expired when click Removal icon in RAID Management ''Physical Device Information'' page.
[Known issue]: 
N/A
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.62.00
==========================================================================
Version: 3.62.00 
Release Date: 2017.10.23

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 0898C0F4
2. rom.ima with MD5 checksum      : E1FF6623AF65DF41E0E5F858B91BD714
3. rom.ima_enc with MD5 checksum  : 71D0C49CBD2A6EF6D54202BCCD142668

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
N/A
[Bug Fixed]:
S5Bx:
1. [200661] There is no Stop located LED button in RAID Management / SAS IT Management tab and is won't stop locate hard drive if user start locate it.
2. [210715] The PTT NV data will be clear after update BIOS by Yafuflash tool
3. [210714] The PTT NV data will be clear after update BIOS by WebUI
4. [209796] The card type of QS-3108-R6-PD32 is different between teraterm's message and spec(Worst card ID list R11).
[Known issue]: 
N/A
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.61.00
==========================================================================
Version: 3.61.00 
Release Date: 2017.10.02

AMI Subversion Revision: AMI SPX RR11.5
Redfish Revision:DTMF 1.1

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 0B6D6FF9
2. rom.ima with MD5 checksum      : 48DCE4A5F9D76C2A3187466C22CD9631
3. rom.ima_enc with MD5 checksum  : 445D67EA1E37F0EFE11C7F10B246601F

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Add redfish feature version 1.1.0
2. Update worst card table R14
3. Add code to set clock buffer for s5bv nvme sku.
4. Remove the ASUS GTX 1080Ti with NVIDIA chip,no i2c interface for s5bv.
5. Add 3s for ac lost time.
6. Modify the time of monitor HDD to BIOS POST END.
7. Avoid prserve sdr when update bmc.
8. Modify the qvoltage.ddf.
9. [208214] WebUI pop-out error message when select RAID volumn operation in ''Logical Device Information'' page.
10. [201729] RAID capacity is empty when create QS3108A-8I RAID with span in Web-UI-RAID Management(create from MSM is pass)
[Bug Fixed]:
S5Bx:
1. [208214] WebUI pop-out error message when select RAID volumn operation in ''Logical Device Information'' page.
2. [201729] RAID capacity is empty when create QS3108A-8I RAID with span in Web-UI-RAID Management(create from MSM is pass)
[Known issue]: 
N/A
[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.60.00
==========================================================================
Version: 3.60.00 
Release Date: 2017.9.15

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 0E2B6504
2. rom.ima with MD5 checksum      : 1A9672D4EC2D6417E6E05272E9CE25C4
3. rom.ima_enc with MD5 checksum  : 5B39D460FFB673E365E0F59D53B27CE2

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Enable Raid management feature.
2. Enable Redfish 1.0
3. Modify the code to monitor nvme ssd after post end.
4. Don't monitor nvme ssd temp if not ready.
5. Always can change the VMD status to mg9098.
6. Add array size for "nvme_drive_fault_count".
7. [209749] Debug console record ''ERROR: I2C8: BUS recovery did not succeed/I2C8: Master-Xfer failed. Bus busy'' log when SUT is DC off.(PSU 1200w*2 + 1 220V power cable)
8. [210334] SAS IT Controller information are empty on BMC WebUI with PMC HBA 1000-8E, have error message ''There are no SAS IT Controller Available [code:1366]''.
9. [194979] WebUI showed empty select item in RAID Management
10. [199736] Connect report SAS IT information in Web page.
11. [200609] BMC v3.05 WebUI ''Physical Device Information'' and ''Topology Information'' show empty information while ''SAS IT Controller Information'' can detect QS3216.
12. [201266] WebUI SAS IT Controller information of QS 3008 IT doesn't match with MCS
13. [208109] WebUI ''RAID Controller Information'' Vendor/Device ID shall be shown in hex format.
14. [209040] Physical Device Information is empty & Topology Information display 65535 after insert new disk in system power off . Boot in RHEL 7.3 and check WebUI information again, it display all information normally.
15. [209049] After plug out disk when Power Off, WebUI Phisical Device Information got error message ''Error in getting SAS IT Physical Information [code:1368]''. Boot in RHEL 7.3 & check WebUI information again, it still got error message.
16. [199985] The error code 1368 is display and Raid controller is empty when click Create virtual device from WEBUI( BMC3.05)
17. [208244] The BMC v3.36 WebUI cannot detect any HBA(Riser2 slot2)/RAID(Riser2 slot1) card when they insert on Riser 2
[Bug Fixed]:
S5Bx:
1. [209749] Debug console record ''ERROR: I2C8: BUS recovery did not succeed/I2C8: Master-Xfer failed. Bus busy'' log when SUT is DC off.(PSU 1200w*2 + 1 220V power cable)
2. [210334] SAS IT Controller information are empty on BMC WebUI with PMC HBA 1000-8E, have error message ''There are no SAS IT Controller Available [code:1366]''.
3. [194979] WebUI showed empty select item in RAID Management
4. [199736] Connect report SAS IT information in Web page.
5. [200609] BMC v3.05 WebUI ''Physical Device Information'' and ''Topology Information'' show empty information while ''SAS IT Controller Information'' can detect QS3216.
6. [201266] WebUI SAS IT Controller information of QS 3008 IT doesn't match with MCS
7. [208109] WebUI ''RAID Controller Information'' Vendor/Device ID shall be shown in hex format.
8. [209040] Physical Device Information is empty & Topology Information display 65535 after insert new disk in system power off . Boot in RHEL 7.3 and check WebUI information again, it display all information normally.
9. [209049] After plug out disk when Power Off, WebUI Phisical Device Information got error message ''Error in getting SAS IT Physical Information [code:1368]''. Boot in RHEL 7.3 & check WebUI information again, it still got error message.
10. [199985] The error code 1368 is display and Raid controller is empty when click Create virtual device from WEBUI( BMC3.05)
11. [208244] The BMC v3.36 WebUI cannot detect any HBA(Riser2 slot2)/RAID(Riser2 slot1) card when they insert on Riser 2

[Known issue]: 

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.46.00
==========================================================================
Version: 3.46.00 
Release Date: 2017.9.8

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 1882E9A8
2. rom.ima with MD5 checksum      : 5447679D731C5BCDDA3B2EF3BE5E35B3
3. rom.ima_enc with MD5 checksum  : 7F5758BEB8491EB12C4869C9F0274A5F

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Fix Etrack 210768 - Event-only sensors are listed in WebUI Disabled Sensor section. (BMC v3.43 WebUI won't shows event-only sensors)
2. Add new GPU support into avl for s5bv. (AUSU GTX 1080Ti.)
3. Update s5bv rep table.
4. Add code to workaround for HDD drive fault.
5. Disable raid management feature.
[Bug Fixed]:
S5Bx:
N/A

[Known issue]: 

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.45.00
==========================================================================
Version: 3.45.00 
Release Date: 2017.9.1

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 137CCE49
2. rom.ima with MD5 checksum      : 3D7BAF90B67A992E0EF1FF0EB6408975
3. rom.ima_enc with MD5 checksum  : 7C51B5C9B88FAA6384B9C9E63F6F86E5

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Change the psu0_status to 0xf6.
2. Speedup fan to 100% when insert non ccl gpu card.
3. [208244]The BMC v3.36 WebUI cannot detect any HBA(Riser2 slot2)/RAID(Riser2 slot1) card when they insert on Riser 2
[Bug Fixed]:
S5Bx:
1. [208244]The BMC v3.36 WebUI cannot detect any HBA(Riser2 slot2)/RAID(Riser2 slot1) card when they insert on Riser 2

[Known issue]: 

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.44.00
==========================================================================
Version: 3.44.00 
Release Date: 2017.8.25

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 139E1FBD
2. rom.ima with MD5 checksum      : 9E7E3A646379EE3EE2AD31BE1DF7CE46
3. rom.ima_enc with MD5 checksum  : 3548FDB8466599E55293EED8C10E06D9

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Add supporting the BIOS version and uefi version of raid card
2. Update the worst card list R12
3. Modify the Riser card slave address to 0xE2
4. Modify the sensor num for psu0/1 status
5. Add gpu function into fsc for S5BV
[Bug Fixed]:
S5Bx:
1. [207524]The detection of GPGPU card and the behavior of FSC control
2. [207493]BMC cannot read ''Temp_GPU1/ 2'' value, but fan duty does not rise to 80%. (Still at low speed)
[Known issue]: 

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.43.00
==========================================================================
Version: 3.43.00 
Release Date: 2017.8.21

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 13A4C543
2. rom.ima with MD5 checksum      : 18F9D8A11AFCE4D86AF7ADAE85D3A36F
3. rom.ima_enc with MD5 checksum  : BD1E9E43C89B8D869E97732EE4AB7D71

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Disable SMI function.
[Bug Fixed]:
S5Bx:
N/A
[Known issue]: 

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.42.00
==========================================================================
Version: 3.42.00 
Release Date: 2017.8.18

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 13A2940E
2. rom.ima with MD5 checksum      : 28F9B62456BEBE4449F0A3D9401A632E
3. rom.ima_enc with MD5 checksum  : 8B706E0D90C107BB74FD74D013299977

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Update oem command for QSM
2. Change the debounce of GPIO_SMI.
2. Add retry for fp fru sku id and event.
3. Modify the hdd monitor delay from bios_post_end to bmc ready+10S
4. Change the me sensor monitor time to 60s after power on and bmc ready.
5. Add code to rise fan speed to max when don't get project/sku ID.
6. Add raid function for supporting all the riser slot 
7. [200665]RAID Controller Information showed empty under WebUI when system plug in with 9361-8i
8. [199304]The BMC v3.02 WebUI SAS_IT_Management cannot get correct SAS-3216B-16I-IT(FW 1A10) information, all SAS IT information should report and correct.
9. [198910]BMC WebUI cannot show RAID/HBA model name (Function do not ready). Purley do not support SAS FRU
10.[208114]WebUI pop-out error message when check ''Storage Summary'' and ''Physical Device Information'' page. (''RAID controller' page can detect 9361-16i info)
11.[207271]S5Bx doesn't support ''In Critical array'' and ''In Failed array'' events, please remove these two events from BMC SDR list and S5Bx Eventlog table v06.
12 [203542]Please update ''S5Bx BMC event table v03.xlsx'' SPEC.(S5BQ not support ?\9CIn a critical array??& ?\9CIn a fail array??(Verify 201736 for found)
13.[208971]Add/Remove disk as Global HotSpare can be successful, but WebUI has been Session Expired every time after set RAID Management
14.[208652]RAID Management information are empty on BMC WEBUI with QS-3008A-IR, have error message ''There are no RAID Controller Available
[Bug Fixed]:
S5Bx:
1. [200665]RAID Controller Information showed empty under WebUI when system plug in with 9361-8i
2. [199304]The BMC v3.02 WebUI SAS_IT_Management cannot get correct SAS-3216B-16I-IT(FW 1A10) information, all SAS IT information should report and correct.
3. [198910]BMC WebUI cannot show RAID/HBA model name (Function do not ready). Purley do not support SAS FRU
4. [208114]WebUI pop-out error message when check ''Storage Summary'' and ''Physical Device Information'' page. (''RAID controller' page can detect 9361-16i info)
5. [207271]S5Bx doesn't support ''In Critical array'' and ''In Failed array'' events, please remove these two events from BMC SDR list and S5Bx Eventlog table v06.
6. [203542]Please update ''S5Bx BMC event table v03.xlsx'' SPEC.(S5BQ not support ?\9CIn a critical array??& ?\9CIn a fail array??(Verify 201736 for found)
7. [208971]Add/Remove disk as Global HotSpare can be successful, but WebUI has been Session Expired every time after set RAID Management
8. [208652]RAID Management information are empty on BMC WEBUI with QS-3008A-IR, have error message ''There are no RAID Controller Available
[Known issue]: 

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.40.00
==========================================================================
Version: 3.40.00 
Release Date: 2017.8.11

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 0DB92CE8
2. rom.ima with MD5 checksum      : 08C51A0AF85EB31F3CE06546178B5F03
3. rom.ima_enc with MD5 checksum  : A84776ABB663E2ABD354BB8CE1F26B08

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Update rep table for s5bv.
2. Remove code of reset system from IERRCrashDumpTask.
2. [190734]Don't support "ipmitool sel time set "MM/DD/YYYY HH:MM:SS" cmd.
3. [200908]Enable smi function.
4. [208092]remove riser temp/riser power sensor on riser slot.
5. [208466]add code to avoid bmc hang when checking hdd type with raid/hba card.
[Bug Fixed]:
S5Bx:
1. [190734] BMC SEL logged two ''Timestamp Clock Sync'' events after change BMC SEL time, but BMC FW spec v0.10 and QCI Eventlog table v2.20 have no this event definition.
2. [200908] [S5Bx] System doesn't record ''SMI timeout'' event after trigger SMI timeout.(Rework MB/ITP trigger)
3. [208092] BMC v3.36 Riser related sensors reading sometimes show ''no reading'' even system is idle and Reboot cycles. (BMC v3.34 pass)
4. [208466] [S5BQ-3540] The BMC will continue reset after update BMC to v3.39 by Linux Remote Console
[Known issue]: 

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.39.00
==========================================================================
Version: 3.39.00 
Release Date: 2017.8.7

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 0DC54224
2. rom.ima with MD5 checksum      : 5B6E6C14202FA5E3A45636EAE9D05FD6
3. rom.ima_enc with MD5 checksum  : 6A8AE0A78E085F69E7E56F88B60056D4

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Fix fan table to correct data

[Bug Fixed]:
S5Bx:
N/A

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.37.00
==========================================================================
Version: 3.37.00 
Release Date: 2017.8.4

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 0DC5C88A
2. rom.ima with MD5 checksum      : 2D302CAC5A008567F7C2B4329059C50F
3. rom.ima_enc with MD5 checksum  : 0559F0F5440BC251CA4B3787E05F039D

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. [206223] WebUI PSU sensor status has extra ''Asserted'' string, and is not friendly for reading becasue no comma between each PSU state.
2. [201499] Fan duty could not breakthrough 75% when system installed the SSD or NVMe SSD. But according to FSC v07, it could reach 100%
3. Fix bmc reset for bmc hanging symptom frequently.
4. According to the hdd type to change the max fan duty.
5. Update the fan table of SKU 3~4 and SKU 5~7 to version 08 
6. Update the PTAS table
7. Update PCIESpecialCardTbl to verison R11. 

[Bug Fixed]:
S5Bx:
1. [206223] WebUI PSU sensor status has extra ''Asserted'' string, and is not friendly for reading becasue no comma between each PSU state.
2. [201499] Fan duty could not breakthrough 75% when system installed the SSD or NVMe SSD. But according to FSC v07, it could reach 100%

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.36.00
==========================================================================
Version: 3.36.00 
Release Date: 2017.7.28

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 17EA2BD6
2. rom.ima with MD5 checksum      : E47AA180BEB44A4CDEE912ECE87FA3F1
3. rom.ima_enc with MD5 checksum  : 3EF70A55974BF06ABCD04C6FEC7AB046

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Add support fsc offset for GPU sensor reading [S5BV].
2. According to the gpu type to change the threshold of GPU Temp sensor[S5BV].
3. Add GPU item into AVL support list[S5BV].
4. Update PCIESpecialCardTbl to verison R11[S5BV].
5. [198910] Fix BMC WebUI cannot show RAID/HBA model name (Function do not ready). Purley do not support SAS FRU.
6. [199304] Fix The BMC v3.02 WebUI SAS_IT_Management cannot get correct SAS-3216B-16I-IT(FW 1A10) information, all SAS IT information should report and correct.
7. [199736] Fix Connect report SAS IT information in Web page.  
8. [199985] Fix the error code 1368 is display and Raid controller is empty when click Create virtual device from WEBUI( BMC3.05) 
9. [200609] BMC v3.05 WebUI ''Physical Device Information'' and ''Topology Information'' show empty information while ''SAS IT Controller Information'' can detect QS3216. 
10.[200665] RAID Controller Information showed empty under WebUI when system plug in with 9361-8i. 
11.[201944] There is no ''SAS IT Management'' in Web UI Setting page. (Mismatch ''SPEC_Standard/ESMS_SPX_User_Guide_HTML5_WebUIv118x.pdf'') (Passed before, separate from 194979 ) 
12.[204187] The threshold of sensor "T_SSD_Highest" mismatched with BMC FW Spec.rev019. 
13.[204742] During BMC update process, system fans shall be in full speed. (inband/outband/WebUI failed)

[Bug Fixed]:
S5Bx:
1. [198910] [S5B_WebUI] BMC WebUI cannot show RAID/HBA model name (Function do not ready). Purley do not support SAS FRU.
2. [199304] The BMC v3.02 WebUI SAS_IT_Management cannot get correct SAS-3216B-16I-IT(FW 1A10) information, all SAS IT information should report and correct.
3. [199736] [3224] Connect report SAS IT information in Web page.
4. [199985] [3540] The error code 1368 is display and Raid controller is empty when click Create virtual device from WEBUI( BMC3.05)
5. [200609] BMC v3.05 WebUI ''Physical Device Information'' and ''Topology Information'' show empty information while ''SAS IT Controller Information'' can detect QS3216.
6. [200665] [PVT_S5B_F2_1_1]RAID Controller Information showed empty under WebUI when system plug in with 9361-8i.
7. [201944] [S5Bx][PVT] There is no ''SAS IT Management'' in Web UI Setting page. (Mismatch ''SPEC_Standard/ESMS_SPX_User_Guide_HTML5_WebUIv118x.pdf'') (Passed before, separate from 194979 )
8. [204187] [PVT_S5B_F2_1_4]The threshold of sensor "T_SSD_Highest" mismatched with BMC FW Spec.rev019.
9. [204742] During BMC update process, system fans shall be in full speed. (inband/outband/WebUI failed)

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 
		
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.34.00
==========================================================================
Version: 3.34.00 
Release Date: 2017.7.14

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 1A5186E2
2. rom.ima with MD5 checksum      : E4DB19399943E622B28EBCA9ADFD5A77
3. rom.ima_enc with MD5 checksum  : 834E0E0995DF0799B25129B15A484522

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07
SKU8~9: v01

[Change/Add]: 
S5Bx:	
1. Add s5bv as sku 8 and sku 9.
2. Support fsc for s5bv.
3. Only support read nvidia gpu Temp.
4. [202642]Fix etrack BMC ''Power difference watt'' event #1. Check SEL by IPMI cmd, event shall show readable sensor type and sensor name. #2. Sensor name is ''BMC FW Info'', not ''BMC FW Health''
5. [204940]Fix BMC can't sent SEL log when we plug in different power watt and different vender power.
6. [205192]Fix EL recorded abnormal event about ''Temperature Temp_BP_2.5 | Upper (Non)critical going high | Asserted when DC cycles under RHEL 7.3

[Bug Fixed]:
S5Bx:
1. [205192] [F2_1_2_DC]SEL recorded abnormal event about ''Temperature Temp_BP_2.5 | Upper (Non)critical going high | Asserted when DC cycles under RHEL 7.3(BP_2.5 connected with Techman PCIe SSD.)
2. [204940] The BMC do not record correct SEL when insert two different Vender/Capacity/PMBUS version PSU into SUT(it record many PSU failure event) (Pass before)
3. [202642] BMC ''Power difference watt'' event #1. Check SEL by IPMI cmd, event shall show readable sensor type and sensor name. #2. Sensor name is ''BMC FW Info'', not ''BMC FW Health''
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.33.00
==========================================================================
Version: 3.33.00 
Release Date: 2017.6.30

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 1A5C8B97
2. rom.ima with MD5 checksum      : 24CB6A898B8D7EA003135235CC36E012
3. rom.ima_enc with MD5 checksum  : D101C538690C99D1EAC290460D4CAB2D

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07

[Change/Add]: 
S5Bx:	
1. [204415] Add unit for voltage sensors of WebUI sensor detail page.
2. [204172] Add condition to avoid to treat as sensor lost if don't device present when BMC init.
3. [190782] Add button event when press power and rst btn even fp has lock.
4. [203109] Fix BMC logged 'SEL almost full' event during BMC cold reset cycle in circular mode.
5. Modify SEL event msg to 'Drive slot (Bay)'

[Bug Fixed]:
S5Bx:
1. [204415] WebUI voltage sensors have no unit in sensor detail page
2. [204172] AC on SUT with one PSU and then insert 2nd PSU with power cable afterward, found system fans are in full speed and 2nd PSU reading are all disabled.
3. [190782] BMC SEL did not record Reset button pressed event when Set lock Reset button of the front panel command and Pressed reset button. (same as #180231)
4. [203109] [Pass before] BMC logged ''SEL almost full'' event during BMC cold reset cycle. (BMC SEL is circular mode)
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.31.00
==========================================================================
Version: 3.31.00 
Release Date: 2017.6.21

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 1D09FD81
2. rom.ima with MD5 checksum      : 74F086987DF2030F4008FF9F2603E88F
3. rom.ima_enc with MD5 checksum  : 5F3A325D951252527751C2045D1A4502

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07

[Change/Add]: 
S5Bx:	
1. modify the platform.S v16 to tune ddr part.
2. update Worst card ID list R10.
3. HW don't follow "S5Bx_sku_table" for MG9098 Mapping for S5B Hybird sku.
4. issue thermal trip event only when "GPIO_IRQ_CPU0/1_THERMTRIP_LATCH_LVC3_N,GPIO_R0/1" is low.
5. remove the sensor T_SSD_Highest for sku3 & 6 & 7.
6. restart lighttpd when it stop.
7. support NVMe SSD temp reading according to the NVMe SSD SPEC.
8. Add patch for MAC before uncompress kernel to avoid hang at AC cycle
9. [203270] - Add reset watchdog as 600 seconds before writing BMC image to flash.
10. Not to enable USB power saving mode at BIOS POST end since BIOS will do it after USB init complete.
11. To BIOS preserve function only Redfish, remove old method.
12. Modify the script in BMC release package for preserve BIOS settings.
13. Modify the cal HDD qty method for fsc. don't cal the rear hdd.
14. Modify the uct/unct of Temp_SAS_Mezz to 115/114.
15. [202280]if the temp is less than the degree in fan table only for temp_Inlet. 
then the duty will assign to the min duty in fan table.
16. fix the VMD issue.
17. [197734] Modify the zone qty when me get fan spped for s5b/s5bq to fix the PTAS issue. 
18. [202642] Modify the sensor name to "BMC FW Info#0x79" for PSU power diff.
19. Modify the bmc watchdog timeout to 30s at runtime.
20. add count when write the system mac to eeprom.

[Bug Fixed]:
S5Bx:
[203270]BMC will crash after flash FW from 3.12 to 3.13 via WebUI with cross different network segment. If want to back to normal, must re-programming BMC FW by fixture.
[202280] System record ''CPU clock throttled'' during the ''stressapp + iperf'' test.
[197734] Thermal PATS report not ready lead to we cannot compare the value with IPMI Zone Fan Speed readings command.
[202642 ]BMC ''Power difference watt'' event #1. Check SEL by IPMI cmd, event shall show readable sensor type and sensor name. #2. Sensor name is ''BMC FW Info'', not ''BMC FW Health''

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin 


==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.13.00
==========================================================================
Version: 3.13.00
Release Date: 2017.5.24

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 1FF6EFC0
2. rom.ima with MD5 checksum      : D8C3C295873930700060D98EE550E18A
3. rom.ima_enc with MD5 checksum  : F09011E5558B3960BC77E37C39E20AC7

[Fan Table]
Version:
S5Bx:
SKU0~2: v12
SKU3~4: v07
SKU5~7: v07

[Change/Add]: 
S5Bx:	
1. [201509]Change to monitor to the NVMe SSD4/5/6/7 for S5B Hybird.
2. Modify the HDD monitor algo.
3. [201547]Igonre the HDD event IFA. (By Matt).
4. [201686] Remove the sensor ''Temp_Riser2 '' and ''Power_Riser2'' for all S5B sku.
5. Modify the sensor type to 0x28 for event "SENSOR_NUM_BMC_FW_HEALTH".
6. Add code to set c value.
7. update Fan table.
8. Modify the HDD/ Card weight.

[Bug Fixed]:
S5Bx:
201509 - BMC v3.11 SDR #1. S5B doesn't have rear HDD, but SDR has two rear HDD sensors. #2. Hybrid SKU NVMe SSD located in HDD4-7, but SDR shows ''Temp_NVMeSSD_0-3''. (Passed before)
201547 - [S5B_PVT_H2_1_1]SEL recorded | Drive Slot HDD7 | In Failed Array | at 256 loop when system setup with Warm boot cycles under windows 2016.(Passed before)
201686 - S5B Riser 2 is only for NVMe cable, it is better not to show sensor ''Temp_Riser2 '' and ''Power_Riser2'' in SDR list. (now shows ''no reading'') 

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.12.00
==========================================================================
Version: 3.12.00
Release Date: 2017.5.12

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 25461569
2. rom.ima with MD5 checksum      : 88103F4FAD912D8B3440CBF5BD471BDA
3. rom.ima_enc with MD5 checksum  : BB5AEBAC391D2DCEB13FD375EFD39574

[Fan Table]
Version:
S5Bx:
SKU0~2: v11
SKU3~4: v05
SKU5~7: v05

[Change/Add]: 
S5Bx:	
1. Add code to block the HDD event.(MG9094_REG_ICA,MG9094_REG_FAIL)
2. modify the wait time after cold/warm boot for HDD monitor. HDD monitor- ~35S 
3. [196611] Add the wait condition after cold/warm boot for ME monitor. ME monitor- 75S
4. [197892] Filter ME event.(evt1-3:0xa0 0x0d 0x01)
5. Disable SMI function.
6. After warm/cold boot, add delay time to hdd monitor.
7. Filter TEMP_SSDx_REAR sensor for S5B.
8. Disable raid management feature.
9. Update S5Bx SKU0~SKU2 fan table.
10. change the gpio_ab1 to input.

[Bug Fixed]:
S5Bx:
197892 - [S5BQ-DVT2][Yafuflash2_v4.16.13] System record abnormal SEL event after OOB update BIOS via Yafuflash2. (Firmware Status - PECI over DMI Interface Error|Image Execution Failed|Firmware Exception)
196611 - [S5B_Hybrid] SEL recorded CPU Temperature log when reboot/AC/DC with W2016 during the cycle.

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.11.00
==========================================================================
Version: 3.11.00
Release Date: 2017.4.28

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 22B518F3
2. rom.ima with MD5 checksum      : 0400A1EC3305F69BC5A5AAD4FBDC0E76
3. rom.ima_enc with MD5 checksum  : DD7D017DB8AFB0018EDF2F7E59BB20B5

[Fan Table]
Version:
S5Bx:
SKU0~2: v04
SKU3~4: v05
SKU5~7: v05

[Change/Add]: 
S5Bx:	
1. Modify the m value to 2 for Power_CPU.
2. Not include the rear ssd temp into higest ssd temp.
3. Modify the me event filter for "CPU Thermal Status" sensor -- 1- PROCHOT
4. Modify the wait time for ME ready.
5. Modify the sdr to match code for sensor "NM Status".
6. Remove SAS HBA Controller support.

[Bug Fixed]:
S5Bx:
191757 - Update ME under RHEL 7.3, #1. BMC ipmi SEL lacks sensor name #2. WebUI SEL mismatch with QCI eventlog table definition #3. BMC FW spec v0.12 has no definition about this event.


[Known issue]: 
1.	RKVM JViewer cannot be launched  by Java8 Update 131

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.10.00
==========================================================================
Version: 3.10.00
Release Date: 2017.4.26

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 24B27FC4
2. rom.ima with MD5 checksum      : D2BF4D9FBD7DDF34D843517C73DD0302
3. rom.ima_enc with MD5 checksum  : B32A46D5917DFFB487772E46632D7CA2

[Fan Table]
Version:
S5Bx:
SKU0~2: v04
SKU3~4: v05
SKU5~7: v05

[Change/Add]: 
S5Bx:	
1. update worst card list R09.
2. [198760]update S5B fan table.
3. [191849]don't clear the "AC ON" flag before read it.(fix the "power policy" issue.
4. [196611][194046]polling ME after BIOS post end.
5. [200611]Modify the IIO string.
6. Modify the NCSI switch function.
7. add wait time and BIOS POST end as condition to read raid lib when raid lib is ready.

[Bug Fixed]:
S5Bx:
198760 - [Tiered SKU] BMC SDR sensor reading shows abnormally, #1. HDD sensor status is ''Not Readable'' #2. All riser related sensors show the same sensor reading #3.Fan zone 0 keep in 16000-18000 rpm.
200611 - [S5B] Severity is ''Unspecified'' in SEL after IIO error injected and event description also display ''undefined event''.
191849 - [S5BF1_1] Setup the ''Restore on AC Power Loss'' policy to ''Power on'', system do not auto power on after restore AC. BMC v2.18 passed
196611 - [S5B_Hybrid] SEL recorded CPU Temperature log when reboot/AC/DC with W2016 during the cycle.
194046 - SEL get CPU0/1 Thermal Sta after unplug single power cable frome PSU side

[Known issue]: 
1.	RKVM JViewer cannot be launched  by Java8 Update 131
2.	NIC selection only can switch Dedicated and Shard NIC(PHY), not support Shard NIC(OCP) ?\9E\C2?auto ncsi lan switch not ready.

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.09.00
==========================================================================
Version: 3.09.00
Release Date: 2017.4.20

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 227B9BB2
2. rom.ima with MD5 checksum      : 6E3C8A88F32DC13686D02C9195FC8985
3. rom.ima_enc with MD5 checksum  : E2F2928EDB8EFB1B27EB4A5E38BE597D

[Fan Table]
Version:
S5Bx:
SKU0~2: v04
SKU3~4: v05
SKU5~7: v05

[Change/Add]: 
S5Bx:	
1. [200611][199861]Change the severity.
2. Modify the polling algo to get once from RAID card after POST END.
3. Due to PCA9554 POR fail, BMC will init it after DC ON. 
4. [200337][200174]Modify the retry algo. for all sensor on the Riser.
5. Add delay time(80s) to wait raid lib ready.

[Bug Fixed]:
S5Bx:
200611 - [S5B] Severity is ''Unspecified'' in SEL after IIO error injected and event description also display ''undefined event''.
199861 - [S5B] Severity of Memory Parity Error not consistent with QCI_SPX_EventLogTable_v4_06 defined.
200337 - [S5B_H1_1_1] During AC cycle test(on cycle 95/175/436), BMC sensor "Temp_SAS_Mezz" have value but system did not install the device.
200174 - [3224] Some sensor reading value mismatch whit golden file during the Reboot/AC cycle test.(Temp_SAS_Mezz/Temp_Riser4/Power_Riser4)

[Known issue]: 
1.	RKVM JViewer cannot be launched  by Java8 Update 131
2.	NIC selection only can switch Dedicated and Shard NIC(PHY), not support Shard NIC(OCP) ?\9E\C2?auto ncsi lan switch not ready.


[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.08.00
==========================================================================
Version: 3.08.00
Release Date: 2017.4.17

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 22B1D397
2. rom.ima with MD5 checksum      : 3CDB3689FF354A6BA7BD96C82645A514
3. rom.ima_enc with MD5 checksum  : C7902BAFBE31AF3F7303AE85A3FE8DC3

[Fan Table]
Version:
S5Bx:
SKU0~2: v04
SKU3~4: v05
SKU5~7: v05

[Change/Add]: 
S5Bx:	
1.[188044] Change the uct & unct to 500 & 1000 for Fan_SYSx_x.
2.[198647] Change the all PSUx naming to PSU0 and PSU1 from PSU1 and PSU2.
3.[199673] Change threshold of the Temp_BP_2.5 & Temp_BP_3.5 and Temp_VR & Temp_VR_CPU0/1 & Temp_VR_CPU0/1_ABC/DEF.
4.[199952][197611] Modify the wrong retry reading for all Temp_NVMe_SSD.
5.[189048]Don't set var to 1 when don't get the correct BMC version.
6. Set circular event as default.
7. Modify the redfish code.

[Bug Fixed]:
S5Bx:
188044 - The threshold value of system fans are not match between BMC FW SPEC v007 and FSC Table R04.
198647 - Current PSU sequence naming rule doesn't follow Mechanical_Std_SPEC definition, including chassis label, MB silkscreen and BMC SDR naming. (PSU numbering should start from 0, but now starts from 1).
199673 - [S5Bx] The Sensor&Threshold value mismatch FSC SPEC define,(S5BQ_FSC Table_R04_QCT_170308), please check sensor value.
199952 - [S5B_PVT_All flash_L6] SEL revorded abnormal event about NVMe [Temp_NVMeSSD_0] [Temperature] Upper Non-Critical when VR stress 60 hours . (Passed before.)
197611 - [S5BQ/Tiered2_1] Run PTU stress found BMC log abnormal NVMe temp event.
189048 - BMC cold reset stress failed at 305 cycles due to BMC version changed to be 0.00. (Issue BMC cold reset again, BMC version can get correct 2.11 version)


[Known issue]: 
1. At BMC FW v 2.26, Update BIOS via WebUI and during BIOS bin file uploading, the progress bar would roll back from 99% and start uploading again until 100%. and updating maybe fail.
2. Befor version 3.05, yafuflash maybe take long time to start the updating process via In-band. 

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.07.00
==========================================================================
Version: 3.07.00
Release Date: 2017.4.13

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 22ABD731
2. rom.ima with MD5 checksum      : 8AFDFB1E44007CE9F48498854C026D30
3. rom.ima_enc with MD5 checksum  : 6BCDC4B87168DE6E04FBEFB1EC4099A7

[Fan Table]
Version:
S5Bx:
SKU0~2: v04
SKU3~4: v05
SKU5~7: v05

[Change/Add]: 
S5Bx:	
1. [199975]Add SENSOR_NUM_BROCAST,0x83,(QuantaPlatform.c)
2. Add the Temp_SSD_Highest sensor.
3. According to the hdd type from BIOS & Raid card(Riser3,3108) to change the max fan speed.
4. updated fan table ver to v05 for s5bq.
5. change the conf file size to 4MByte from 1MByte.

[Bug Fixed]:
S5Bx:
199975 - [S5B] Sensor number and severity do not correct on sensor ''BroadcastSts''.(Passed before.) 

[Known issue]: 
At BMC FW v 2.26, Update BIOS via WebUI and during BIOS bin file uploading, the progress bar would roll back from 99% and start uploading again until 100%. and updating maybe fail.

[Notice]:
	1. Due to BMC's conf extend to 4MB, yafuflash and webui does not support BMC upgrade from previous version.
	2. Update BMC FW via command line:
    		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
    		b) in DOS, run "dos.bat".
	   		in Window, run "win.bat"
       			in Linux, run "linux.sh"
	3. Force to update BMC FW via command line:
    		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	4. Update BMC FW via Web UI:
    		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	5. login account:
    		a) IPMI access account for WEBGUI and IPMITOOL.
       			username: admin
       			password: cmb9.admin

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.05.00
==========================================================================
Version: 3.05.00
Release Date: 2017.3.30

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 23E6556F
2. rom.ima with MD5 checksum      : 6C7812C7FF66AED2F819C55B10D64377
3. rom.ima_enc with MD5 checksum  : 992E9601B2D528AA47C251DC7249B44C

[Change/Add]: 
S5Bx:	
1. Change sensor name to Temp_NVMeSSD_R_0 and Temp_NVMeSSD_R_1.
2. Modify all the virtual media instance(cd-rom/floppy/hdd) number to 1.
3. [196263][194826][194824][194823]Modify the HDD monitor algo.
4. Add lnct 5 and lct 0 for sensor Temp_Inlet.
5. Remove event "almost full event" when enable sel circular.
6. Modify the lnct and lct to 1000 and 500 for Fan_SYSx_x.
7. Enable preserve MAC function.
8. [194268] Modify the "Fan present - Deasserted" event severity to Critical.
9. [194401][194833][199640][199488][195183][199430][194888]Unckeck psme agent. 

[Bug Fixed]:
S5Bx:
196263 - The BMC SEL(v2.27) will record many HDD event(present/failure/rebuild...etc.) at WIN 2016 AC/DC cycle test loop 48 and loop 53
194826 - [S5B 1&1 ESP]The BMC SEL(v2.24) sometimes will record full HDD present deasserted/asserted when run WIN2016 AC cycle test(most time only record ''HDD 2/3 present deasserted'')(HDD 2/3 do not insert HDD)
194824 - [S5B] During AC cycle test, HDD slot driver present event did not consistent on each cycle. Sometimes only record slot 8-11, sometimes record slot 0-11.
194823 - [S5B_Hybrid] During AC cycle test, BMC will record ''HDD slot 8-11 Driver present'' event, but Hybrid system only have 8 HDD slot.
194268 - WebUI shows ''Fan present'' event severity is question mark.
194401 - [S5BQ] Run VR stress under RHEL over weekend and found BMC die.
194833 - [S5B 1&1 ESP] There are some abnormal bmc event logs after warmboot test on CentOS6.8 x64
199640 - Unable to ping BMC IP and check BMC heartbeat is off at DC cycle 27 loop.
199488 - [S5B] System record abnormal SEL log(Drive Present/Add-in Card SD Card/Power Unit Power Unit | AC lost) during DC/warm reboot test.
195183 - [DVT2_Hybrid_LBG4_PCHB1_3PCIe] The BMC will cannot be accessed and BMC heartbeat LED not light at Warm boot cycle 888 loop.
199430 - [3224_2] System record abnormal SEL log(Drive Present/Add-in Card SD Card/Power Unit Power Unit | AC lost) during the CPU stress test.(PTU)
194888 - [S5BQ] [LBG-1_Full] System occurred ''Health BMC FW Health | Management controller off-line'' and ''PCIe Error | Bus Correctable error'' and ''Add-in Card |  | Asserted'' event during warmboot cycle test.

[Known issue]: 
At BMC FW v 2.26, Update BIOS via WebUI and during BIOS bin file uploading, the progress bar would roll back from 99% and start uploading again until 100%. and updating maybe fail.

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.04.00
==========================================================================
Version: 3.04.00
Release Date: 2017.3.23

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : F6A1890C
2. rom.ima with MD5 checksum      : BF3D719BA3759E09DBDFC8C0067E088B
3. rom.ima_enc with MD5 checksum  : D6E84017C274E2C8D598ABCE4BED994A

[Change/Add]: 
S5Bx:	
1. Add NVMe SSD Temp sensor at rear for sku 3 & 6 & 7. 
2. Modify the "Monitor interval" to 1 for sensor "DIMM & PSU & Inlet Temp".
3. [194355] Add fan table version shown on webui.
4. [191757]Add sensor "NM Status", sensor number:0x8f.
5. Enable Redfish function.
6. Remove SAS fru (ID:10).
7. [190782] Don't send power btn event when lock "Power OFF button".
8. Change below severity.
#[198103 ] PostError
0x00D5 to warning.
0xA104 to warning.
#[198622] Event Reading Type:0x76
"CPU Critical Temperature - Asserted" to Critical
#SDR Type C0h - OEM Record
To Information.

[Bug Fixed]:
S5Bx:	
198103 - WebUI ''No space for Legacy Option ROM'' event severity is ''Information'', but QCI Eventlog table v4.03 defines ''Warning''.
194355 - According to BMC std spec v2.22 that WebUI shows fan table version for CMC FW, but S5B doesn't support CMC still can see ''Fan Table Version'' item in WebUI.
198622 - [S5B] According to spec ''QCI_SPX_EventLogTable'' defined the Severity of ¡§CPU Critical Temperature asserted¡¨ is be ¡§Critical'' not ''Warning''.
190782 - BMC SEL did not record Reset button pressed event when Set lock Reset button of the front panel command and Pressed reset button. (same as #180231)
191757 - Update ME under RHEL 7.3, #1. BMC ipmi SEL lacks sensor name #2. WebUI SEL mismatch with QCI eventlog table definition #3. BMC FW spec v0.12 has no definition about this event.

[Known issue]: 
At BMC FW v 2.26, Update BIOS via WebUI and during BIOS bin file uploading, the progress bar would roll back from 99% and start uploading again until 100%. and updating maybe fail.

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.02.00
==========================================================================
Version: 3.02.00
Release Date: 2017.3.16

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 3250042D
2. rom.ima with MD5 checksum      : FE9DE186D7107B3AA1A467744293F5AB
3. rom.ima_enc with MD5 checksum  : 0B2F24D8C102385D1DF644716DD03882

[Change/Add]: 
S5Bx:	
1. disable Redfish.
2. don't speed up fan to full when sensor don't present.
3. change the Generator ID for log me event.

[Bug Fixed]:
S5Bx:	

[Known issue]: 
At BMC FW v 2.26, Update BIOS via WebUI and during BIOS bin file uploading, the progress bar would roll back from 99% and start uploading again until 100%. and updating maybe fail.

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.01.00
==========================================================================
Version: 3.01.00
Release Date: 2017.3.14

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : F46F85DA
2. rom.ima with MD5 checksum      : 78F4D40B37CB359AF5F6C5CF9CCD5585
3. rom.ima_enc with MD5 checksum  : B27EDEA9B22A748D147EDD2368F84FD7

[Change/Add]: 
S5Bx:	
1. Support Redfish.

[Bug Fixed]:
S5Bx:	

[Known issue]: 
At BMC FW v 2.26, Update BIOS via WebUI and during BIOS bin file uploading, the progress bar would roll back from 99% and start uploading again until 100%. and updating maybe fail.

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B series AST2500(A2) BMC FW Release v3.00.00
==========================================================================
Version: 3.00.00
Release Date: 2017.3.9

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 3270DBB9
2. rom.ima with MD5 checksum      : 730CCB699E75D3DCDD751BBAFC0C595B
3. rom.ima_enc with MD5 checksum  : 114C492125269CCA471288DB6A43B311

[Change/Add]: 
S5Bx:	
1. [187866] Add the inventory function.
2. [191271] Remove the unnecessary BP temp for all sku.
3. [194011] Change sensor num as below. CPU0 to 0xA9, CPU1 to 0xAC, HDD2 to 0xB3... HDD11 to 0xBC.
4. [189051][194268][194273][197008] Modify the sel severity.
5. [194297]modify the lct to 5 for Temp_Inlet.
6. [187900] Disable 'dumped kernel messages'.
7. Remove sensor "Temp_OCP_Mezz_In".
8. Change the hdd/PCIe weight and sensor num/name for S5BQ.
9. Add CPU offset for PID.
10. Remove sensor "System Event" sen#0x72.
11. change dimm related sensor name.
12. Enable BMC watchdog.
13. WebUI support HBA card in riser4.
14. RAID managment only supports riser 3 type 1 slot 1 and riser 3 type 2.
15. Change the lct to 2.520 and uct to 3.591 for sensor Volt_P3V_BAT.
16. Change the "HDD present - Deasserted" as default status.

[Bug Fixed]:
S5Bx:	
194297 - MRD v2.19 defines lowest operational temperature is 5 degree C, but BMC sensor ''Temp_Inlet'' LCT threshold is 12 degree C, the temperature difference is large.
187866 - [RR11.5/WebUI] Unable to detect the DIMM_A0 under BMC WebUI System Inventory page.
191271 - All Flash/Tiered SKU only use? 2.5" BP but SDR still has sensor "Temp_BP_3.5" that shows "no reading".
194011 - In WebUI "Sensor" page, some HDD/CPU sequence are reversed.
189051 - After install RHEL 7.3 OS, BMC SEL in WebUI shows OS boot event severity is unknown and sensor name ''#0x0''.
194268 - WebUI shows ''Fan present'' event severity is question mark.
194273 - QCI Eventlog table v2.21 ''Fan Present'' event #1. Lacks? ''Fan Present - Asserted'' definition #2. ''Fan Present'' event description not match with WebUI shows.
197008 - WebUI "BMC hardware watchdog timeout reset" event severity and description doesn't match with QCI Eventlog table v4.03.
187900 - [T2_1/H1_1 /F2_3]  Front Panel ID LED blinking frequency is not consistent

[Known issue]: 
At BMC FW v 2.26, Update BIOS via WebUI and during BIOS bin file uploading, the progress bar would roll back from 99% and start uploading again until 100%. and updating maybe fail.

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v2.31.00
==========================================================================
Version: 2.31.00
Release Date: 2017.2.24

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 3288D363
2. rom.ima with MD5 checksum      : D0A898F9F9E48FAA73B486C1B1DCCA71
3. rom.ima_enc with MD5 checksum  : 1F0737A092E45F31FBAE4F9CF6236993

[Change/Add]: 
S5Bx:	
1. add code to support complete BASIC FSC(PID).

[Bug Fixed]:
S5Bx:	

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v2.30.00
==========================================================================
Version: 2.30.00
Release Date: 2017.2.21

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 3286950D
2. rom.ima with MD5 checksum      : 9CCCCB0BC93737BF0C5F7F1A1CA6451D
3. rom.ima_enc with MD5 checksum  : DE7DF30F1765F02A6B31675ECFBDC384

[Change/Add]: 
S5Bx:	
1. [196605] Fix BMC reset issue.

[Bug Fixed]:
S5Bx:	
[196605] [S5B] Cannot reset BMC by IPMI command on BMC v2.29. (v2.28 passed).

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v2.29.00
==========================================================================
Version: 2.29.00
Release Date: 2017.2.20

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 32866EDD
2. rom.ima with MD5 checksum      : 3F570F71E6B41EC02C57B88FA2820A93
3. rom.ima_enc with MD5 checksum  : BCDB47D5C8D31774B66157D4FDCF0B2A

[Change/Add]: 
S5Bx:	
1. fix fan table loading issue when all sku.
2. Mark code for command QuantaSetPCIECardInfo to avoid bmc hang.
3. "ipmi cold reset" command would be rejected when doing bmc/bios update.

[Bug Fixed]:
S5Bx:	

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v2.28.00
==========================================================================
Version: 2.28.00
Release Date: 2017.2.16

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 05ADBD27
2. rom.ima with MD5 checksum      : 548FDE2F334DA90EAB504732C4C6043A
3. rom.ima_enc with MD5 checksum  : 12E399DCC894478AEEF5ED55CCDDEF37

[Change/Add]: 
S5Bx:	
1. Add fan table support for all sku.
2. Disable redfish.
3. Add NVMe SSD LED control.
4. Fix HDD monitor issue for sku of 12 pcs HDD.
5. Modify the Temp and fan sensor threshold for S5BQ.

[Bug Fixed]:
S5Bx:	

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v2.27.00
==========================================================================
Version: 2.27.00
Release Date: 2017.2.9

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 35093BB0
2. rom.ima with MD5 checksum      : 6AE868F2D78F4494C10E5245A4E99BA7
3. rom.ima_enc with MD5 checksum  : 03322CF491C472FBBE81158E388ACF34

[Change/Add]: 
S5Bx:	
1. Fix sensor Power_CPU and Power_Memory issue.
2. Remove the unnecessarily sensor by sku.
3. Add code to read NVMe SSD Temp.
4. Fix bmc hung issue when dc cycle.
5. Add event data 2/3 in psu status to identify OTP, OVP, OCP and fan fault.
6. RAID managment only supports solt 1 in type 1 riser and slot 1 in type 2 riser.
7. Disable redfish.

[Bug Fixed]:
S5Bx:	

[Known issue]: 
1. Don't support HDD status monitor for sku0/1/2/3.

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
==========================================================================
        S5B series AST2500(A2) BMC FW Release v2.25.00
==========================================================================
Version: 2.25.00
Release Date: 2017.1.26

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 37DAEF9B
2. rom.ima with MD5 checksum      : 16CD0C35B798F3A707C413BFE2CFAA18
3. rom.ima_enc with MD5 checksum  : 34277D0B95F93A82F99CC74D9B71135B

[Change/Add]: 
S5Bx:	
1. HDD sensor status default to present.
2. Support SAS/STAT HDD status for all sku.
3. Add S5BQ Fan table.
4. Disable redfish.

[Bug Fixed]:
S5Bx:	

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B series AST2500(A2) BMC FW Release v2.24.00
==========================================================================
Version: 2.24.00
Release Date: 2017.1.20

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 380F6672
2. rom.ima with MD5 checksum      : 485C1D93B7C1BEC426E6BC9AD3A65ED2
3. rom.ima_enc with MD5 checksum  : 09283C97A673DEAE35C35B7D9AAE3A08

[Change/Add]: 
S5Bx:	
1. Modify the slave addr of Riser4 INA219 to 0x84.
2. Add sensor#0xf8 for sd card.
3. Enable USB by default next version, SIT to verify HOST not hang (by mail)
4. Modify compcode of Set BMC Configuratio and Get BMC Configuration to 0xd5 if not support.
5. Change the sensor number for mb_thermaltrip.
6. [189217] BMC preserve MAC address before update bios.
7. [191643] Restore pid control to PID when ME self test result change to normal.
8. [188929] enable usb.
9. Disable PEF instances.
10. Disable redfish.
11. raid management: only support riser 3 type 2. 

[Bug Fixed]:
S5Bx:	
[189217] [S5B] Offline update BIOS or via BMC Web-UI update, the PHY board MAC address will be removed. Suggest BMC have put the solution from Web-UI update BIOS if any emergency occur during BIOS boot up.
[191643] The Fan speed do not return normal status when reboot SUT after flash BIOS 2A08 under WIN2016(DC on/off SUT will make Fan speed return normal status)
[188929] [H5_1] System is easy to be hung up at 0xB4 after AC/DC/reboot (Similar 187061)

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B series AST2500(A2) BMC FW Release v2.23.00
==========================================================================
Version: 2.23.00
Release Date: 2017.1.12

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 2CB84565
2. rom.ima with MD5 checksum      : C4F9F2F6D7A221ECC5FD7471D2818BF7
3. rom.ima_enc with MD5 checksum  : 404480A2CE66A4EB397C282AE50213BD

[Change/Add]: 
S5Bx:	
1. Modify "Sensor Maximum" and "Sensor Minimum" of Temp_Riser3 to 0x7f and 0xc5.
2. Add "power on delay" of Riser temp sensor.
3. [188046][190289] Modify the default present status for sensor HDD,FAN,PSU,PSU Redundancy,etc. 
4. [191965] Add sensor Temp_Riser2#0x6B and Power_Riser2#0xe8.
5. [191947] Add below function to S5BQ.
	a. filter cpu0/1 thermal status.
	b. HDD status monitor.
	c. send event when psu power difference.
	d. psu cold redundant.
6. [190976] Update OEM command ¡§SET PCIE INFORMATION¡¨ request Byte.
7. [190913] Add support HDD status on SNMP.
8. [190843] sensor "PSU Redundancy" will show Fully Redundant only when both PSU status equal 0x01.
9. [191847] Modify the sensor "Assertion/Deassertion mask and settable readable threshold to show LCT threshold.
10. [191957] modify the sensor initialization and capabilities to show sensor reading.
11. uncheck "Runtime Feature Licensing Suppport".

[Bug Fixed]:
S5Bx:	
[188046] [F2_3] The BMC didn't record the ''Fan_SYSx_Status | Device Present | Asserted'' after plug the system fan.
[190289] SEL should not log ''Power Supply PSU Redundancy | Fully Redundant | Asserted'' when BMC cold reset.
[191965] [S5BQ] BMC lack Riser 2 Temp & Power sensor.
[191947] [3224_1_1 LBG-1]SEL sensor got HDD 0 ''na'' incorrectly 
[190976] OEM ''Get PCIE Information'' response all 0 when SUT installed with two LSI9300-8e storage cards, one X550-T2 lan card and one OCP 82599ES mezz 
[190913] Failed to get SNMP ''hddDeviceInfoTable'' information and it would pop-out error message ''Request failed or timed out. No error''. card.
[190843] Trigger PSU OT to make one PSU failure and input 0 watts, but PSU Redundancy still shows ''Fully Redundant''.
[191847] According to BMC std spec v2.20 that inlet temperature sensor should have LCT threshold, but now S5B doesn't have.
[191957] [S5BQ] BMC 2.22 found ''BMC_CPU_Util '' & ''BMC_Mem_Util '' show as disable. Please check it.

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B series AST2500(A2) BMC FW Release v2.22.00
==========================================================================
Version: 2.22.00
Release Date: 2017.1.6

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 2CC0166D
2. rom.ima with MD5 checksum      : 0E84EB6791A8FF0E336132B98108B841
3. rom.ima_enc with MD5 checksum  : 7F41BD30F683FDC3B7FEFCE954273129

[Change/Add]: 
S5Bx:	
1. Modify BIOS sensors.
2. Change the SENSOR_NUMBER_AMBIENT_1 at code to 0x76 for mb_thermal_trip.
3. [191786] Change the description of BMC Chipset version to AST2500(A2) at file ReleaseNote.txt.
4. [191090] Set  Volt_PVCCIO_CPU1 to uct:1.057V and lct:0.882V. 
5. [191849][191809] Fix ipmi cmd "power on" issue.
6. [190084] Change the sen# HDD2 to 0xbc and CPU0 to 0xac
7. [191847] Add lct 0x0c for Temp_Inlet.
8. [191691] Modify BMC OEM command 0x3A(Get Asset ID) to match OEM SPEC v2.3.
9. [191852] Modify the debounce for below GPIOs.
	GPIO_ID_BTN_N,GPIO_FP_RST_BTN_N,GPIO_FP_PWR_BTN_N,GPIO_FP_NMI_BTN_N
10. Modify the sdr setting for sensor BMC_CPU_Util and BMC_Mem_Util.

[Bug Fixed]:
S5Bx:	
[191090][S5BQ] System occurred ''Voltage Volt_PVCCIO_CPU1 | Lower Critical going low '' during PTU stress test.
[191786] WebUI BMC Chipset version was mismatch with release note. (WebUI:AST2500(A2), release note:AST2500).
[191809] SUT has no response to ipmi chassis power command and WebUI power action.
[190084] The Severity is ''Information'' for event ''[HDD2] [Drive Slot] Drive Fault - Asserted'', it should be ''Critical''. (HDD3~HDD11 are Passed.)
[191847] According to BMC std spec v2.20 that inlet temperature sensor should have LCT threshold, but now S5B doesn't have.
[191849] [S5BF1_1] Setup the ''Restore on AC Power Loss'' policy to ''Power on'', system do not auto power on after restore AC. BMC v2.18 passed[]
[191691] The BMC OEM command 0x3A(Get Asset ID) feedback data do not match OEM SPEC v2.3 define(SPEC define feedback data should be BMC MAC, but actual feedback data are all ''ff'')
[191852]  Sometime UID LED always blinking after turn ON to OFF  by press UID button repeat several time

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B series AST2500 BMC FW Release v2.20.00
==========================================================================
Version: 2.20.00
Release Date: 2016.12.29

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. Yafuflash2 (version 4.16.13)

[Firmware Images]:
1. rom.ima with checksum          : 382C7009
2. rom.ima with MD5 checksum      : 52C7BC006562D899EF7679108CF61E35
3. rom.ima_enc with MD5 checksum  : DD418C98C57EE22083D989C6BBD877E4 

[Change/Add]: 
(S5B/S5BQ):
1.[188689] Upgrade the uboot verison to v14.
2.[189719][188747][187539] Add condition to filter ME event.(CPU0/1 Thermal Sta)
3.[191195] Disable SD Server. Host/OS can't access it.
4.[189418][191090][190356] Add Aspeed ADC solution. the same as RR2 soultion.
5.[190964] Support ONE PSU or TWO PSU config. BMC will scan and change the config once AC on.
6.[181774] Support PSU cold Redundancy by OEM command (0x36/0x1c).
7.[191318][191419] Change below voltage sensors monitor policy.
Volt_P3V_BAT, Volt_PVNN_PCH, Volt_P1V8_PCH, Volt_P12V_AUX, Volt_P1V05_PCH.
8.[190771] BMC has increased the judgment during get sensor reading.
9.[190899] BMC has increased sensor name and sensor type on 'oem Record cx' event.
10.[188227] Modify the format of Memory ECC Error log in the SMTP server
11.[190754] Chagne sensor states from ''All deasserted'' to ''All Deasserted'
12.[188762] Modify the counting method under MibBrowser.


[Bug Fixed]:
S5B/S5BQ:	
[188689] BMC hang up during hot and cold operational test
[191318] Some voltage sensors belong to standby sensors, their reading shall be available when system is DC off. (according to BMC std spec v2.20 sec.5.1.1)
[191419] [S5BQ]Some voltage sensors belong to standby sensors, their reading shall be available when system is DC off. (according to BMC std spec v2.20 sec.5.1.1)
[189418] [H5_1][B1 PCH] SEL recorded abnormal event ''[Volt_P1V8_PCH] [Voltage] Lower Critical - Going Low'' after idle under RHEL 7.3.
[191090] [S5BQ] System occurred ''Voltage Volt_PVCCIO_CPU1 | Lower Critical going low '' during PTU stress test.
[190356] [3224_2] System recode Voltage PVCCIO_CPU1/P3V_BAT critical log after power on the SUT
[190964] [S5B] For two PSU SKU. Plug out one PSU power cord, BMC SEL did not record ''Power Supply PSU Redundancy | Redundancy Lost'' event.
[181774] Cold redundancy no function\
[190771] All fans status are ok, but SNMP fanStatusOverall shows "other".
[190899] WebUI login event in SNMP "selDeviceInfoLogTable" shows incorrectly. (sensor name is empty, sensor type is "Temperature")
[188227] For Memory ECC Error log, description in PEF Mail is not consistent with SNMP Trap and WebUI.
[190754] WebUI discrete sensor states shall change from ''All deasserted'' to ''All Deasserted'' to match other sensors format.
[188762] [RR11.5/SNMP] The FRU data was incomplete and missing lot of feilds under MibBrowser. 

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		Refer to readme.txt
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B/S5BQ AST2500 BMC FW Release v2.18.00
==========================================================================
Version: 2.18.00
Release Date: 2016.12.12

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 388134F0
2. rom.ima with MD5 checksum      : 2BA67009F9967514ECE804519A191751
3. rom.ima_enc with MD5 checksum  : A3DAADE1CFA950C743C64439A3D54A91

[Change/Add]: 
(S5B/S5BQ):
	1.Update voltage threshold
	2.disable PSU event
	3.disable PEF control

[Bug Fixed]:
S5B/S5BQ:	

	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B/S5BQ AST2500 BMC FW Release v2.17.00
==========================================================================
Version: 2.17.00
Release Date: 2016.12.8

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 388452F8
2. rom.ima with MD5 checksum      : 60F33889E45E11B4569CDA235D21695D
3. rom.ima_enc with MD5 checksum  : DF0D63718D8695A429A5FF92A68AE375

[Change/Add]: 
(S5B/S5BQ):

[Bug Fixed]:
S5B/S5BQ:	
	[189323] Sensor ''CPU_Utilization'' and ''Mem_Utilization'' reading are inaccurate, not match with OS reported CPU/memory loading.
	[189320] WebUI shows ''CPU_Utilization'' and ''Mem_Utilization'' sensor type are ''Reserved'', and BMC spec v0.08 section 5 doesn't define these two sensors for detailed info.
	[189402] WebUI login fail event severity and description different with QCI_SPX_EventLogTable_v2_18 definition. (other login events description are also different with standard)
	[189575] Disable BMC IPv6 support in BIOS setup, found WebUI shows BMC IPv6 status is ''Static''.
	[188227] For Memory ECC Error log, description in PEF Mail is not consistent with SNMP Trap and WebUI.
	[188494] [RR11.5/SMASH] The PSU Redundancy status is not correct when system DC OFF. (Same issue as S2B #184420)
	[188241] Mail server cannot receive mail for event ''OEM Record cX''.
	[188233] SEL would not record event ''PEF Action - Asserted'' when trigger event with PEF Mail Enabled. (Have received mail in mail server.)
	
	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B/S5BQ AST2500 BMC FW Release v2.16.00
==========================================================================
Version: 2.16.00
Release Date: 2016.11.29

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 3B49C384
2. rom.ima with MD5 checksum      : 0356EBF52B6713BC2AD5FF64AE6C74BD
3. rom.ima_enc with MD5 checksum  : 7E727E779475121DEF9EFAAA2EFED792

[Change/Add]: 
(S5B/S5BQ):
	(1) support BMC 64M Flash (MX25L51245GMI-08G)
	(2) disable Redfish
[Bug Fixed]:
S5B/S5BQ:	
	[188740] The Description is showed ''undefined'' for events ''[Power Supply] Predictive Failure'' and ''[Power Supply] Power Supply Failure Detected''.
	[188966] [F2_1]SEL recorded abnormal ''undefined BIOS event'' when inject DIMM configuration problem on DIMM J/K/L/M
	[189215] WebUI fan present event severity is unknown and QCI_SPX_EventLogTable v2.18 doesn't define this event.
	[189299] Disable ME to make Temp_PCH reading not available, found system fans duty didn't rise up to 100%.
	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B AST2500 BMC FW Release v2.15.00
==========================================================================
Version: 2.15.00
Release Date: 2016.11.24

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 318AB2E0
2. rom.ima with MD5 checksum      : F6D7D33785CBF2D7CAA24B7515F43153
3. rom.ima_enc with MD5 checksum  : E78900F2528DEC748B8B1650573A7873

[Change/Add]: 
(S5B):
	
[Bug Fixed]:
S5B:	
	[186432] [T2_1] SEL recorded a lot of Volt event during AC power cycling. ''[Volt_DIMM_ABC]'', ''[Volt_DIMM_KLM]'', ''[Volt_PVCCIO_CPU0]'', ''[Volt_PVCCIO_CPU1]'', ''[Volt_P3V_BAT]'', ''[Volt_PVNN_PCH]''
	[186732] [T2_1] SEL recorded abnormal SPS FW Health events  ''UMA Operation Error - Asserted'' and ''Auto-configuration Finish - Asserted'' at DC power cycling about 11Hrs/108 cyles
	[187395] [T2_1] SEL recorded duplicated events in some loops during BIOS + ME online flash stress.
	[187621] [BMC RR11.5] As discussed in BMC FG meeting, (1)pls provide the SDR table for S5B (like the definition for AMA), (2)pls define to Std_SPEC.
	[187432] For ''Additional PCI Express Error Events Log'', the Sensor Name and Sensor Number havn't been defined to BMC SPEC and Event Table 2.15.
	[188250] [RR11.5/WebUI] It's hard to distinguish the grayed-out info on WebUI Power Control page.
	[188490] [RR11.5/SMASH] (1) Please update the SMASH definition for RR11.x code base. (2) There is no ''Note 2'' for LOM/OCP Mezz/Quanta Mezz.
	[188739] [F1_1, H1_1] BMC WebUI got timeout disconnect under RKVM virtual CD mounted and web idle on Dashboard.
	[189215] WebUI fan present event severity is unknown and QCI_SPX_EventLogTable v2.18 doesn't define this event.
	[188747] [All flash SKU] System record abnormal log ''Processor CPU0 Thermal Sta/Processor CPU1 Thermal Sta'' during hot and cold operational test
	[188997] [S5B_H1_1] One of the S5B system, BMC sensor reading value have deviation on sensor ''Volt_DIMM_XXX''. (BMC show 1.28-1.27 Volts, but actually only 1.21-1.20 Volts)
	[189290] BMC v2.11 supports fan LNC threshold (945 rpm), but according to BMC standard spec v2.17 the value should be NA. 
	[189635] BMC SDR check fail
	[189637] Micro SD card Fail
	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B AST2500 BMC FW Release v2.13.00
==========================================================================
Version: 2.13.00
Release Date: 2016.11.18

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 375195AE
2. rom.ima with MD5 checksum      : 7EEADDEDC187B1284F9DD134165835D5
3. rom.ima_enc with MD5 checksum  : 144C476A17530213C9BC6CA64014CCA4

[Change/Add]: 
(S5B):
	[1] Add MB Thermal Trip behavior

[Bug Fixed]:
S5B:	
	[175851] BMC WEBUI can't get  PSU Predictive failure detail information. (OTP / OCP / .....)
	[186744] ''No Signal'' message showed up on BMC RKVM during system warmboot (system Power LED was steady ON).
	[186969] The naming format of PSU OT and UV failure event didn't follow the QCI_SPX_EventLogTable_v2_15.
	[187259] [RR11.5/WebUI] (1) The FRU Product Information page didn't print out the ''Product Part Number'' and ''Product Version''. (2) The IPMI tool didn't print out the ''Product Serial Number''.
	[187539] [F2_3] There are some abnormal SEL ''Processor CPU1 Thermal Sta |  | Asserted'' be recorded during AC Lost/Redundancy test.(similar to 186850)
	[187659] SEL log missing on WebUI after triggered Temp_VR_DIMM event. (e.g. log 27 then 32; 28-31 are missing).
	[187668] Unspecified/undefined event has been recorded after triggered Temp_VR_DIMM event. 
	[188210] [T4_1] DC cycle test and BMC will record #0x0/ [OS Boot] [OS Stop or Shutdown] log , sensor name shouldn't be ''[#0x0]''
	[188494] [RR11.5/SMASH] The PSU Redundancy status is not correct when system DC OFF. (Same issue as S2B #184420)
	[188738] [RR11.5/SNMP] (1) Unable to detect the DIMM A0 via MibBrowser. (2) Unable to detect all DIMMs freuency via MibBrowser.
	[188750] [RR11.5/SNMP] The manufacture and model name of processor was shown ''Unknown'' under MibBrowser.
	[188762] [RR11.5/SNMP] The FRU data was incomplete and missing lot of feilds under MibBrowser.
	[188780] [RR11.5/SNMP] The MibVersion was incorrect which be loaded under MibBrowser.
	[189051] After install RHEL 7.3 OS, BMC SEL in WebUI shows OS boot event severity is unknown and sensor name ''#0x0''.
	[189196] AC off and then AC on, SUT power on immediately once BMC heartbeat start blinking, without randomly waiting 0-10 seconds to power on.
	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B AST2500 BMC FW Release v2.11.00
==========================================================================
Version: 2.11.00
Release Date: 2016.11.05

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 376FE4BA
2. rom.ima with MD5 checksum      : 766373483BF9449FB35D79C7A86F8A18
3. rom.ima_enc with MD5 checksum  : 7E19DEED9CDAEFE8EF501D3F7423B2F6

[Change/Add]: 
(S5B):
	[1] Add PSU Cold Redundancy, but default is Cold Redundancy mode for SDA testing, v2.12.00 will set default to be Normal mode.
	[2] Add fan fail mechanism for fan control.

[Bug Fixed]:
S5B:	
	[188255] [RR11.5/WebUI] The current page will not be refreshed when press the same icon from menu bar.(Grantley passed)
	[188252] [RR11.5/WebUI] Please define in more detail about the meaning of ''Warning'' icon since it's not for SEL.
	[188250] [RR11.5/WebUI] It's hard to distinguish the grayed-out info on WebUI Power Control page.
	[188235] [RR11.5/WebUI] The WebUI will pop-out message ¡§Invalid Password¡¨ when change the SNMP access setting from ''User Management Configuration'' page.
	[188174] [RR11.5/SNMP] The default SNMP community string is incorrect under BMC FW 2.08.(doesn't meet BMC Std_SPEC 2.17)
	[188162] [BMC RR11.5] (1)Unable to get the reading from sensor ''Temp_OCP_Mezz'' and (2)sensor ''Temp_OCP_Mezz_In'' has be implemented to BMC 2.08, please define to BMC FW SPEC.
	[188044] The threshold value of Temp_PCH dose not match between BMC FW SPEC v007 and FSC Table R04.
	[188029] [RR11.5/WebUI] The BMC WebUI should not allow the user to login with privilege level ''User''.
	[188024] [RR11.5/WebUI] (1)No ''OEM Proprietary'' in drop-down menu with user privilege. (2)The level of ''None'' shall be the ''No Access''.
	[187900] [T2_1] Front Panel ID LED blinking frequency is not consistent
	[187859] [RR11.5/WebUI] The format of BMC Firmware Revision doesn't match between BIOS setup (2.08.00) and BMC WebUI (2.08.0)
	[187558] Sensor Number ''0x90'' cannot be decoded and BMC SPEC v007 doesn't have related definition.
	[187459] Sensor Name ''CPUX Thermal Sta'' doesn't be defined to Event Table 2.15
	[187457] SEL doesn't record Thermal Trip event when system is thermal trip and then auto power off.
	[187453] WebUI status is Processing and no any response while UUT Processor Hot test
	[187437] New WebUI SEL log format for PCIe Error (should report solut number) is not ready. (New definition in BIOS Standard V3.05-Draft)
	[187231] [RR11.5 WebUI] The quantity of IPMI Event Log didn't sync the current SEL quantity.
	[187218] [RR11.5/WebUI] The BMC WebUI will pop out the error message when using the Backup Configuration.
	[187152] (1)MB FRU VRC package lack FRU.bin file and (2)ReadMe info is incorrect.
	[187137] [RR11.5/Basic Fun] Failed to flash 63 digit for FRU info ''MB Serial Number'' as SPEC definition (Actual Max :44).
	[187092] One keyboard pressed, abnormally got multiple response by BMC Web RKVM.
	[186744] ''No Signal'' message showed up on BMC RKVM during system warmboot for 20 mins(system Power LED was steady ON).
	[186736] [T2_1] SEL recorded Critical event ''[Fan_SYS5_0] Lower Critical - Going Low'' and Warning event ''[Fan_SYS5_0] Lower Non-Critical'' during DC power cycling about 4 hours/40 cyles
	[186514] The sensors of ''Temp_Outlet'' and ''Airflow'' (ME function) unable to get the reading (separate from #186228).
	[186421] [T2_1] Front Panel System Status LED blinking frequency is not consistent.
	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B AST2500 BMC FW Release v2.09.00
==========================================================================
Version: 2.09.00
Release Date: 2016.10.22

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 37851701
2. rom.ima with MD5 checksum      : 5351009B6DE3C769C0D41086C060836B
3. rom.ima_enc with MD5 checksum  : 9731F8EC2C0C46676F78B56BEFB44417

[Change/Add]: 
(S5B):

[Bug Fixed]:
S5B:	
	[182807] The BMC didn't record any event when unplug the PSU from PSU slot.(Slot 1/2) (separate from issue 181568)
	[186514] The sensors of ''Temp_Outlet'' and ''Airflow'' (ME function) unable to get the reading (separate from #186228).
	[186574] [RR11.5 WebUI] The function of SAS IT Management has been removed from BMC RR11.5 WebUI, please update ESMS SPEC (v101) if no support.
	[186575] [RR11.5 WebUI] The function of System Firewall has been removed from BMC RR11.5 WebUI, please update ESMS SPEC (v1.01) if won't support it.
	[186659] [F2_3] The Quanta ICTS Test was failed on ''Set Sensor Event Enable'' and ''Get Sensor Event Enable'' with tool QICTS0.16.
	[186816] [F2_3] Quanta ICTS Inband Test failed on ''Set Sensor Event Enable'', ''Get Sensor Event Enable'' and ''Set LAN Configuration Parameters#72'' with tool QICTS0.16. (similar to #186659 for outband)
	[187558] Sensor Number ''0x90'' cannot be decoded and BMC SPEC v007 doesn't have related definition.
	[187565] [RR11.5/WebUI] There is an abnormal character be displayed when update BIOS FW via WebUI.
	[187608] [AST2500] BMC WebUI RKVM has no screen(No Signal) once system boot to DOS environment.(AST2400 passed)
	[187818] [RR11.5/SNMP] The SNMP version doesn't match between the actual trap Type and WebUI Settings.
	[187231] [RR11.5 WebUI] The quantity of IPMI Event Log didn't sync the current SEL quantity.
	[188116] It should be capital letter for Proper Nouns ''Bios'' and ''Post'' of POST Error log in WebUI.
	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin

==========================================================================
        S5B AST2500 BMC FW Release v2.08.00
==========================================================================
Version: 2.08.00
Release Date: 2016.10.11

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 3CB50187
2. rom.ima with MD5 checksum      : A7C01F2A136CDF81BB0D92E18AA0B96A
3. rom.ima_enc with MD5 checksum  : 9D76AA39C84C81F3418BAF7560C71044

[Change/Add]: 
(S5B):
      Add support SNMP function.

[Bug Fixed]:
S5B:	
		
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin


==========================================================================
        S5B AST2500 BMC FW Release v2.07.00
==========================================================================
Version: 2.07.00
Release Date: 2016.10.06

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 3CB6CCA0
2. rom.ima with MD5 checksum      : DE7D4D04BEF874137A334668CF06DB21
3. rom.ima_enc with MD5 checksum  : D10F87DB453721883BE3F3AEB7F8FA90

[Change/Add]: (S5B)

[Bug Fixed]:
S5B:	[175851] BMC WEBUI can't get PSU Predictive failure detail information. (OTP / OCP / .....) 
		[186228] There are some sensors unable to get the reading, ''Temp_BP_3.5'', ''Temp_Riser1'', ''Temp_Riser3B'', ''Temp_PCH'', ''Temp_Outlet'' and ''Airflow''. 
		[186307][Suggestion] Please check the possibility to implement the feature ''BIOS POST Code'' to BMC WebUI as BMC did for Grantley platform.
		[186353][H1_1] BMC record abnormal SEL ''Management controller off-line'' when idle or execute warmboot cycling test. [186575][RR11.5 WebUI] The function of System Firewall has been removed from BMC RR11.5 WebUI, please update ESMS SPEC (v1.01) if won't support it.
		[186370][H2_1]BMC recorded abnormal event about ''Power Supply PSU2_Status | Predictive failure | Deasserted '' and ''Processor CPU0/1 Thermal Sta'' when system stress under windows server 2016. 
		[186969] The naming format of PSU OT and UV failure event didn't follow the QCI_SPX_EventLogTable_v2_15. 
		[187142][RR11.5/Basic Fun.] Max FRU size still show 256bytes, it should be 512 for Purley.
		[187182][RR11.5/WebUI] (1)Snapshot ''BIOS POST code'' in SPEC ''ESMS_SPX_User_Guide_HTML5_WebUIv103'', please define in detail and (2)BIOS POST "c"ode should use upper case 
		[187241] [RR11.5/WebUI] The current FRU Device ID only implement ''0'' and ''1'', please also add the ID 10 and ID 16 for NIC&SAS FRU.
		[187243][RR11.5 WebUI] The FRU Device Name of ID 0 doesn't match with current FRU via ipmitool.
		[187313] The current SNMP community string is different from the definition of BMC Standard SPEC v2.16.
		[187396] BMC Sensor Reading cannot monitor correct value for Temp_VR_CPU0 and Temp_VR_CPU1.
		
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
		
==========================================================================
        S5B AST2500 BMC FW Release v2.06.00
==========================================================================
Version: 2.06.00
Release Date: 2016.09.22

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 3E418F14
2. rom.ima with MD5 checksum      : E67C9A09CE33D839062CA222D819C017
3. rom.ima_enc with MD5 checksum  : 484DF38A00B3E7543FE1245A5385525A

[Change/Add]: (S5B)

[Bug Fixed]:
S5B:	[180592] [RR11] There is no BMC SEL be recorded after perform ACPI shutdown by WebUI->Power Control.
		[180595] [RR11] Unable to detect the product name from current FRU field on WebUI->FRU Information.
		[181620] The BMC is not ready for BIOS Out-of-Band flash.(separate from 181620).
		[180661] Incorrect FRU info and setting on the latest VRC FRU version 0.3.
		[186448] Unable to detect the BMC chipset under BMC WebUI->Dashboard->Device Information.
		[186454] The BMC WebUI Dashboard function of ''Power Cycle - Up Time'' always keep on ''4d 6hrs'' after perform the power control (Off/Reset/Cycle).
		[186457] [F2_3] The BMC will record ''Microcontroller/Coprocessor #0x16 | Transition to Running'' during the power control test.
		[186458] The function of Sensor Monitoring could not detect the PSU ERROR SDR under BMC WebUI/Dashboard/Sensor Monitoring.
		[186511] (1)Please add notice to remind user the consequence if unlock Preserve checkbox (2)notice for "Preserve all configuration" is not proper
		[186512] Continued tracke #186510, failed to download SEL log text file from WebUI.
		[186757] [F2_3] The BMC I2C stress test failed at ''bus=1 addr=0x94'' and the default account/password of tool shall be ''qct.admin''.
		[186785] The network communications protocol ''HTTP'' should be disabled and support ''HTTPS'' only under RR11.5 Redfish functions.

[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: cmb9.admin
		
==========================================================================
        S5B AST2500 BMC FW Release v2.05.00
==========================================================================
Version: 2.05.00
Release Date: 2016.09.08

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 40CD9EC9
2. rom.ima with MD5 checksum      : 399129FA091BF754F643945B6FAD1853
3. rom.ima_enc with MD5 checksum  : 71F0B9CD5C2D49D4B48B344DC62EA702

[Change/Add]: (S5B)

[Bug Fixed]:
S5B:	[179643] (SKX-F, LBG LAN) BMC has no temperature sensor for OCP2.0 NIC devices.
		[179650] (SKX-F, LBG LAN) BMC has no FRU file for OCP2.0 NIC devices.
		[186228] There are some sensors unable to get the reading, ''Temp_BP_3.5'', ''Temp_Riser1'', ''Temp_Riser3B'', ''Temp_PCH'', ''Temp_Outlet'' and ''Airflow''.
		[186395] [All] System failed to power on by press Power button before BMC ready.(should be OK according to BMC Std. v2.14).
		
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: qct.admin
		password: qct.admin

==========================================================================
        S5B AST2500 BMC FW Release v2.04.00
==========================================================================
Version: 2.04.00
Release Date: 2016.09.01

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 4127736C
2. rom.ima with MD5 checksum      : 06CA087383DEF1C6C2388F43BD985E77
3. rom.ima_enc with MD5 checksum  : 5CE153C6E51F2C3970B5E5925E9C1173

[Change/Add]: (S5B)

[Bug Fixed]:
S5B:	[178251] (3.5'' Hybrid) Abnormal BMC SEL recorded after flash BIOS 1A03 ME from 1A03 under Win2012R2.	
		[182957] BMC will record abnormal log ''[Unknown][Slot or Connector](undefined state) - Asserted'' and ''[PCH Thermal Trip][Temperature]State Asserted - Asserted'' during reboot from windows.
		[186041] BMC record incorrect 2 times [Power off/down] log when DC power off(expected is 1).
		[186043] [H4_1]BMC record system DC power ON log incorrectly "[Power off/down Asserted]" (should be Deasserted) according to Std_event table spec
		[180631] [Hybrid_B1] BMC record error log ''Unknown ME FW Health'' and ''Watchdog '' during DC stress.
		[186186] There are lots of BMC SEL only report sensor number (sensor name for PSU, Temperature are missing)
		[186124] [H2_1]BMC recorded abnormal event about Power Supply PSU1_Status and Temperature #0x57  when Warmboot test under RHEL 7.2
		[186110] [H4_1] Abnormal BMC SEL(sensors a3/34/67) for system AC power cycles.
		[186194] The sensor number of 34h, 40h, 66h, 67h and A3h haven't been defined to Projecgt BMC SPEC v06.
		[186182] [F1_1] Both our LBG1 systems were failed to DC ON after MB FRU flash.(ok to boot if disable BMC)
		[186204] The sensor name of PSU_Redundancy does not match with project BMC Spec v06.
		[183146] After inject ''ei.injectUpiError(0,0,1)'',it showed''[Unknown][Processor] Correctable Error(undefined Processor event)/ CPU 0/ QPI Port 0 - Asserted'' (separate from issue 180469)
		[180518] It would show ''(undefined Memory event)'' for Correctable ECC event after injected Memory ECC Correctable Error to  DIMM E0/E1/F0/F1/L0/L1/M0/M1.
		[181381] [RR11] Please defines if the RR11 or RR11.5 support the SOL setting as RR2 (separate from  #180554).
		[186189] Failed to download SEL log from WebUI via IE 11.0.34. (Firefox 48.0.2 is Passed)
		[186201] [T4_1] BMC record critical logs about memory during DC power cycle under RHEL 7.2.
		[179964] [RR11] There are 48 sensors got the critical status on BMC Web with BMC FW 1.07.
		[178715] BMC SEL timestamp is incorrect during AC cycle(Incorrect timestamp is 01/01/2012)
		[173820] MicroSD no function
		[179966] [RR11] There are 14 Temp sensors got the 0 degrees C with BMC FW 1.07.
		[181461] Both two CPU PROCHOT LED on MB light ON after switch BIOS chip with new FW 1A06.
		[181774] Cold redundancy no function
		[180336] [Hybrid_B1] BMC didn't record error log when user insert two different PSU(PSU_1 DPS-500AB-14 A  / PSU2 DPS-750AB-30 A)
		[182807] The BMC didn't record any event when unplug the PSU from PSU slot.(Slot 1/2) (separate from issue 181568)
		[186046] [H4_1]BMC time check failed after boot in RHEL72 and idle 3mins, time difference getting bigger by time.
		[186068] (1)with ARP environment, the BMC will record lots of ''Temperature BroadcastSts'' event and full SEL up very quickly. (2)also help clarify why this sensor belongs to Temperature..
		[186182] [F1_1] one of our systems was failed to DC ON after FRU/BoardID flash.(ok to boot if disable BMC)
		[186202] ''Chassis Power'' and  ''Temp_DIMM_DEF''.use duplicated sensor number #ADh.
		[186206] [F2_3] The SUT would not reboot after executed the IPMI command ''ipmitool chassis power reset''.
		
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: qct.admin
		password: qct.admin

==========================================================================
        S5B AST2500 BMC FW Release v2.03.00
==========================================================================
Version: 2.03.00
Release Date: 2016.08.22

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 41DFB2E3
2. rom.ima with MD5 checksum      : E04716D24308F7D1F59AD204DF55D69A
3. rom.ima_enc with MD5 checksum  : 6DAFE95468260B0CFF7A2197BE25C6F0

[Change/Add]: (S5B)
1. Enable Fan Speed Control

[Bug Fixed]:
S5B:	[178533] ''Shared NIC(OCP Mezz)'' setting in BIOS Setup /BMC LAN port config cannot be saved successfully
	[179968] [RR11] The BMC Web page of Sensor would keep on loading and halt with BMC FW 1.07.
	[180105] The MB-FRU flash fail under RHEL 7.2 if using the script in S5B-MB (LBG-4)-3.zip (VRC ID#83921).
	[180568] [RR11] The BMC SEL could not be restored after perform the Backup/Restore function for all configurations in Maintenance Menu.
	[180592] [RR11] There is no BMC SEL be recorded after perform ACPI shutdown by WebUI->Power Control.
	[184866] BMC cannot connect with ON82599 if set ''BMC LAN port'' configuration to ''Shared-NIC(OCP Mezz)'' ,Intel X540 is PASS. 
	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: qct.admin
		password: qct.admin

==========================================================================
        S5B AST2500 BMC FW Release v2.02.00
==========================================================================
Version: 2.02.00
Release Date: 2016.07.28

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 42A2631F
2. rom.ima with MD5 checksum      : 142E7519658ABD16A40FA5A2825E08D7
3. rom.ima_enc with MD5 checksum  : 976C45F0FFFDC889C15C970442592FD3

[Change/Add]: (S5B)

[Bug Fixed]:
S5B:	[179726] [Hybrid]BMC RKVM doesn't work.
	[181314] [RR11] The current SDR name of ''BMC FW Health'' do not match with BMC FW SPEC v004 (separate from #178790).
	[183375] Some DC power cycles took longer (about 100s) than average. (separate from issue 179365)
	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: qct.admin
		password: qct.admin

==========================================================================
        S5B AST2500 BMC FW Release v2.01.00
==========================================================================
Version: 2.01.00
Release Date: 2016.07.21

AMI Subversion Revision: AMI SPX RR11.5

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 42C0DD7B
2. rom.ima with MD5 checksum      : B31D401A4B962AAF906EBAAFFFD4AC2A
3. rom.ima_enc with MD5 checksum  : 808720F8BDF95CCEC0D84B2168CFB335

[Change/Add]: (S5B)

[Bug Fixed]:
S5B:	[173991] BMC function is not ready for TE to develop Diagnostic tool
	[177573] (2.5'' All Flash)BMC will disconnect if configuration address source with Static address or using DHCP from CMS.
	[178961] BMC WEBUI can upload ''rom.ima'' and it should pop out error message to notice user.
	[180552] [RR11] The function of VMCli is not ready, please implement the VMCli for test.
	[180632] BMC LAN port LED turned OFF after 12hrs broadcast storm stress.
	[178531] Ping BMC directly via Dedicate-NIC and it has some packages lost.
	[178536] BMC WebUI is not ready for user to update BIOS.
	[178715] BMC SEL timestamp is incorrect during AC cycle(Incorrect timestamp is 01/01/2012)
	[178936] BMC LAN port configuration cannot changed in BIOS/ Server Mgmt/, always keep at Dedicated-NIC after changed the item to another setting save and reset.
	
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: qct.admin
		password: qct.admin

==========================================================================
        S5B AST2500 BMC FW Release v1.10.00
==========================================================================
Version: 1.10.00
Release Date: 2016.06.03

AMI Subversion Revision: AMI SPX RR11

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 55C63210
2. rom.ima with MD5 checksum      : 0F5307411458F792A3E33C52AF919AA5
3. rom.ima_enc with MD5 checksum  : B9C797671CED1B4D2D72BC6D2523BFCF

[Change/Add]: (S5B)
S5B:	Add ME sensor: Airflow and Temp_Outlet

[Bug Fixed]:
S5B:	177382 [Stress](2.5'' All Flash)The system got many failed messages after running StressAPPtest under RHEL 7.1
		178364 [2.5'' All Flash]BMC is not ready for read CPLD version and checksum
		178779 The sensor of Temp_Inlet and Temp_Outlet are disappear on current sdr list. 
		178783 The sensors naming format of FAN_SYSx_x do not match with BMC FW SPEC rev001, the correct name please refer to ''Std_BMC_SPEC_SYS_FAN.jpg''. 
		180091 [Hybrid_B1] There is an error recorded ''Invalid/Unsupported Command'' during the PMBus stress test.
		180153 SEL recorded CATERR_MCERR but not CATERR_IERR after triggered CATERR_IERR by ITP fixture. 
		180364 The first letter for all of ''Sensor Type'' in WebUI is not upper case.
		180557 A lot of abnormal event generated when try to trigger Thermal Trip.
		180624 There is no ''Fan redundancy lost'' SEL when unplug SUT fan module, mismatch to Std. Event table definition for redundancy fan.
		180630 BMC SNMP Community String is ''AMI'', mismatch to Std. definition(S5B BMC FW SPEC also with incorrect ''Quanta'').
		180839 SEL recorded a lot of abnormal event ''[Volt_PVNN_PCH]'' and ''[Volt_PVCCIN_CPU0]'' after injected Memory ECC Uncorrectable error via MEI fixture.
		181043 [Hybrid_B1]  BMC v1.08.00 has no  "Processor CPU_x present", but 1.09.00 has, release note should add this change list.
		181054 [Hybrid_B1] Sensor ''QEventOnly'' and ''Chassis Power'' has not be defined to BMC SPEC 0.03
		181082 [Hybrid_B1] CPU sensor name(CPU_0) didn't match QCI_SPX_EventLogTable_v2_10 (CPU0)
		181312 [RR11] There are 3 SDRs use to the same sensor number ''B2h'' between the current BMC FW v1.09 and BMC SPEC v004 (separate from #178790).
		181314 [RR11] The current SDR name of ''BMC FW Health'' do not match with BMC FW SPEC v004 (separate from #178790). 
		181309 [RR11] Please sync the SDR's naming rule of ''Fan_SYSx_x'' between BMC Std SPEC and EventLog Table (separate from  #178783).
		181568 [Hybrid_B1]  BMC record ''Unknown'' event during un-plug/plug PSU (side effect of issue 180346)  
		
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: admin

==========================================================================
        S5B AST2500 BMC FW Release v1.09.00
==========================================================================
Version: 1.09.00
Release Date: 2016.05.19

AMI Subversion Revision: AMI SPX RR11

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 55CEC79D
2. rom.ima with MD5 checksum      : DFCB1A7E99D06D7BB65E1E3B241DCFBC
3. rom.ima_enc with MD5 checksum  : 74F09C2270CF0B53AD0B61053DFCE044

[Change/Add]: (S5B)
S5B:	Add Processor CPU_x present event when CPU detected

[Bug Fixed]:
S5B:	
		178592 - (3.5'' Hybrid) Unplug power cord of PSU1, BMC continually record abnormal PSU1 Predictive failure/Failure SEL during SUT stress test.
		178599 - (ALL SKU) ID LED didn't act very well when press Front panel ID Button.
		178715 - BMC SEL timestamp is incorrect during AC cycle(Incorrect timestamp is 01/01/2012)
		178801 - ''Last state'' for Restore on AC Power Loss in not workable, system not power on after restore AC power.
		179632 - The SUT not power on automatically after AC off then AC on if ''Restore on AC Power Loss'' set to ''Last State'' in BIOS setup.
		179756 - [Hybrid] Status LED didn't blink when remove power cord (SEL severity is critical ''Power Supply Input Lost (AC/DC) - Asserted'' )
		179970 - [RR11] The sensor reading of Temp_DIMM_x would display abnormal symbol by ipmitool v1.8.15.
		180367 - Sensor Name is ''Unknown'' for event ''TCC Activation''.
		180389 - Severity of event ''TCC Activation - Asserted'' is Critical, but QCI_SPX_EventLogTable_v2_10 defined it should be ''Warning''.
		180395 - The Sensor Number of event ''TCC Activation - Asserted'' is not correct (BMC SPEC rev.003 : it should be 7Ch,7Dh)
		180433 - Sensor Name ''Temp_CPU0'' and ''Temp_CPU1'' (BMC1.08) and BMC SPEC 0.3. are not consistent with ''QCI_SPX_EventLogTable_v2_10''
		180591 - [RR11] The BMC SEL ''Temperature Temp_CPU0/1 - UC/UNC'' be recorded after perform the Hard Reset by WebUI->Power Control.
		180644 - Unknown FRU info(ID 1) after SUT flash the latest VRC FRU version 0.3.
		180848 - [Hybrid_B1] BMC didn't record ''Fan present-Deasserted" event when user removed fan.
		
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: admin



==========================================================================
        S5B AST2500 BMC FW Release v1.08.00
==========================================================================
Version: 1.08.00
Release Date: 2016.05.05

AMI Subversion Revision: AMI SPX RR11

[Utility]:
1. SOCFLASH (version v.1.12.03)

[Firmware Images]:
1. rom.ima with checksum          : 55BD6AE9
2. rom.ima with MD5 checksum      : E0D19AFD5322E20836F759FB90D745EC
3. rom.ima_enc with MD5 checksum  : 8C645FD5DB0706E783CA958B0B9A3107

[Change/Add]: (S5B)
S5B: Add NVMESSD_X temperature of 2.5" HDD BP

[Bug Fixed]:
S5B:	178406 - [Hybrid] BMC LAN LED's behavior is incorrect(Link LED is always blinking.)
		179473 - [Hybrid] "BMC Cold Reset" test failed(2 cycles).
		179585 - [Hybrid] BMC will record PSU log after BMC cold reset 
		179632 - The SUT not power on automatically after AC off then AC on if ''Restore on AC Power Loss'' set to ''Last State'' in BIOS setup.
		179737 - [Hybrid]Fan will stop for 20~30 seconds during BMC update(The behavior didn't match with BMC standard SPEC)
		179846 - for Rossi.Lin to approve >> [Hybrid] BMC supported session for RMCP/RMCP+ in S5B BMC FW Spec.rev002 is 36, but actually only supported 15.
				
[Known issue]: 
N/A

[Notice]:
	1. Update BMC FW via command line:
		a) put dos4gw.exe, socflash.exe, and rom.ima in same directory.
		b) in DOS, run "dos.bat".
		   in Window, run "win.bat"
		   in Linux, run "linux.sh"
	2. Force to update BMC FW via command line:
		a) run "socflash if=XXXX.ima -s option=x flashtype=2" in DOS.
	3. Update BMC FW via Web UI:
		a) Please select rom.ima_enc as image file and doesn't upload Signimage key.
	4. login account: 
		a) IPMI access account for WEBGUI and IPMITOOL.
		username: admin
		password: admin


=====================================================================
        S5B AST2500 BMC FW Release
=====================================================================
Version: 1.07.00
Release Date: 2016/04/28

[Utility]:
1. SOCFLASH (version v.1.12.03 )

[Firmware Images]:
1. rom.ima with checksum          : 55BA95DC
2. rom.ima with MD5 checksum      : DF571FEF60E8B350EED4EBAEF4FC52F3
3. rom.ima_enc with MD5 checksum  : 2B4736BFAC617C688F1132464C43A3BA

[Notice]:
1. This version is used to do EVT test.
2. Please use IPMI command to check sensor monitor. (ipmitool sensor list)
3. Please use IPMI command to check event. (ipmitool sel elist)

[Changed]:
1. Synchronize with AMI patch included ASPEED patch v9(update to 2016/04/26)
3. Add TjMax for fan control

[Bug Fixed]:
[178969] Add Broadcast issue solution to solve AC cycle stress failed 
[178790/178787/177859/178783/175250/178784/178774] update spec
[178801]fix "Last state" for Restore on AC Power Loss

[Known issue]:
1. Disable BMC JTAG interface for HW CPLD Upgrade


=====================================================================
        S5B AST2500 BMC FW Release
=====================================================================
Version: 1.06.00
Release Date: 2016/03/25

[Utility]:
1. SOCFLASH (version v.1.12.03 )

[Firmware Images]:
1. rom.ima with checksum          : 573EAED2
2. rom.ima with MD5 checksum      : 4FA179C9FB1D6AC29E2BE23CA06DEBAE
3. rom.ima_enc with MD5 checksum  : CF719B37EF4D57A49180C9DFC2BDB79A

[Notice]:
1. This version is used to do EVT test.
2. Please use IPMI command to check sensor monitor. (ipmitool sensor list)
3. Please use IPMI command to check event. (ipmitool sel elist)

[Changed]:
1. BMC Power Restore Policy (random delay in 10 seconds to power on) 
2. Synchronize with AMI patch
3. Add PCH thermal sensor (Supported from PCH QKR6 version)
4. fix only read one PSU status

[Bug Fixed]:

[Known issue]:
1. Disable BMC JTAG interface for HW CPLD Upgrade
2. Web server is ready, but UI function is not ready
3. When DC cycle, ME will issue OEM event:PECI over DMI interface error ,checking with Intel

=====================================================================
        S5B AST2500 BMC FW Release
=====================================================================
Version: 1.05.00
Release Date: 2016/03/11

[Utility]:
1. SOCFLASH (version v.1.12.03 )

[Firmware Images]:
1. rom.ima with checksum          : 5764D015
2. rom.ima with MD5 checksum      : 511B01DB8F8E1E88365655E228F85DE4
3. rom.ima_enc with MD5 checksum  : 4C05508EC405B02876B228CAC97DD9D1

[Notice]:
1. This version is used to do EVT test.
2. Please use IPMI command to check sensor monitor. (ipmitool sensor list)
3. Please use IPMI command to check event. (ipmitool sel elist)

[Changed]:
1. Add PSU Present/ Redundancy/ Fan Direction Error
2. Modify PSU Temperature (follow QCT PMBus Command)
3. Add PSU Data Command (MFR Revision/FW Revision)
4. Add CPU_DIMM_VRHOT
5. Add CPU_DIMM_HOT
6. BMC Power Restore Policy (delay 5 seconds to power on) 
7. Delay 120 seconds to monitor ME sensor (Waiting BMC ready)  

[Bug Fixed]:

[Known issue]:
1. Disable BMC JTAG interface for HW CPLD Upgrade
2. DIMM/PCH Sensor is not ready,checking with Intel IPS#6000153718
3. Web server is ready, but UI function is not ready
4. When DC cycle, ME will issue OEM event:PECI over DMI interface error ,checking with Intel

=====================================================================
        S5B AST2500 BMC FW Release
=====================================================================
Version: 1.04.00
Release Date: 2016/02/24

[Utility]:
1. SOCFLASH (version v.1.12.03 )

[Firmware Images]:
1. rom.ima with checksum          : 579E57E9
2. rom.ima with MD5 checksum      : B21F6DA3B1168A2BD73B671011905BB3
3. rom.ima_enc with MD5 checksum  : B08F022DE0CA1A3E79783B5833218E02

[Notice]:
1. This version is used to do EVT test.
2. Please use IPMI command to check sensor monitor. (ipmitool sensor list)
3. Please use IPMI command to check event. (ipmitool sel elist)

[Changed]:
1.Add power on time count

[Bug Fixed]:
[174541]DC stress failed with many error log (Voltage / Temperature / Processor /PSU...)
[174584]System LED didn't blink when FAN failed
[174603]"Volt_VR_CPU_1" and "Temp_VR_CPU1" reading is ''No Reading'' (CPU_0 : Passed)
[175373]Heat temp sensor(Temp_Ambient_FP) to trigger upper critical threshold and system status LED didn't blink. (similar to S5B #174584)
[175450]BMC FW package(s5bv1020) didn't include windows update tool(DOS and Linux is ready)
[175732]I2C Stress test failed (S5B_i2c_test_v01) (Port80 is all "OFF" and ping BMC IP sometimes failed)

[Known issue]:
1. Disable BMC JTAG interface for HW CPLD Upgrade
2. DIMM/PCH Sensor is not ready,checking with Intel IPS#6000153718
3. Web server is ready, but UI function is not ready
4. When DC cycle, ME will issue OEM event:PECI over DMI interface error ,checking with Intel

=====================================================================
        S5B AST2500 BMC FW Release
=====================================================================
Version: 1.03.00
Release Date: 2016/02/04

[Utility]:
1. SOCFLASH (version v.1.12.03 )

[Firmware Images]:
1. rom.ima with checksum          : 57A5DA1D
2. rom.ima with MD5 checksum      : EEE6FDAC20F016054D48EEB4B85A7DE0
3. rom.ima_enc with MD5 checksum  : 137899B7DCEB06F20A9968A2FF5BADFD

[Notice]:
1. This version is used to do EVT test.
2. Please use IPMI command to check sensor monitor. (ipmitool sensor list)

[Changed]:
1.Add OEM command for SD card test
2.GPIO Interrupt event (CAT ERROR/PCH Thermal Trip/CPUx THERMTRIP)


[Bug Fixed]:
[173812] It becomes slow to operate under BIOS Setup menu .
[173643] BMC didn't record related SEL when MB CATERR LED ON.
[174512] Fan sensor(Dual rotary Fan) name of SDR info is incorrect (doesn't meet ME SPEC and BMC SPEC)
[174569] BMC inband command didn't work after SUT reboot in Windows (using AMI solution for Bootloader issue)
[174599] CPU temp sensor is missing from SDR list
[174603] "Volt_VR_CPU_1" and "Temp_VR_CPU1" reading is ''No Reading'' (CPU_0 : Passed)

[Known issue]:
1. Disable BMC JTAG interface for HW CPLD Upgrade
2. DIMM/PCH Sensor is not ready,checking with Intel IPS#6000153718
3. Web server is ready, but UI function is not ready
=====================================================================
        S5B AST2500 BMC FW Release
=====================================================================
Version: 1.02.00
Release Date: 2016/01/21

[Utility]:
1. SOCFLASH (version v.1.12.03 )

[Firmware Images]:
1. rom.ima with checksum          : 57B12555
2. rom.ima with MD5 checksum      : EAB5A1EE970B8531523A75F085ED46DE
3. rom.ima_enc with MD5 checksum  : 6C4A48C5B000908BA0A8D9FF1A11698C

[Notice]:
1. This version is used to do EVT test.
2. Please use IPMI command to check sensor monitor. (ipmitool sensor list)

[Changed]:
1.Add Thermal sensor(FP/BP/Riser/MB/PSU),not include CPU/DIMM/PCH
2.Support MB/FP FRU
3.Support I2C 0~13 
4.fix Fan sensor reading
5.Use official SOCFLASH v.12.03

[Bug Fixed]:
1.[173629] Fix BMC Self-test

[Known issue]:
1. Disable BMC JTAG interface for HW CPLD Upgrade
2. CPU/DIMM/PCH Sensor is not ready,checking with Intel IPS#6000151390
3. Web server is ready, but UI function is not ready


=====================================================================
        S5B AST2500 BMC FW Release
=====================================================================
Version: 1.01.00
Release Date: 2016/01/04

[Utility]:
1. SOCFLASH (version v.test.0 )

[Firmware Images]:
1. rom.ima with checksum          : 57DC5986
2. rom.ima with MD5 checksum      : 9093DAF636805FE62E7137DC7BCDB904
3. rom.ima_enc with MD5 checksum  : 6E42F865B98389AF6FE00C3FEFD9C59B

[Notice]:
1. This version is used to do EVT test.
2. Please use IPMI command to check sensor monitor.

[Changed]:
1.First EVT release version

[Bug Fixed]:
N/A

[Known issue]:
1. Disable BMC JTAG interface for HW CPLD Upgrade
2. ME Sensor is not ready
3. Web server is ready, but UI function is not ready
4. Official SOCFLASH tool for Purley platform is not released
